background image

14

15

Note:

The »Design Kettle Cool Touch« is no measuring appliance. There may be diffe-

rences between the temperature displayed on the display and the actual tempera-

ture of the water. Using the temperature selection buttons, you may change the set 

temperature any time you like before and during operation (see below: ‘Selecting 

the Desired Temperature’).

 

 Simply press the ON/OFF button to start the boiling cycle. On the display the set 

temperature is shown and the kettle starts heating immediately. With none of the 

temperature selection buttons pressed, the set temperature is always “100”°C.

As soon as the water reaches the set temperature, the kettle turns off. To activate 

keep warm function press the „keep warm“ button. Keeping the water hot for at 

up to 30 minutes. Thereafter, the kettle will shut off and the display gets dark.

IMPORTANT:

 The maximum water temperature of the keep warm function is limited 

to 90 °C, because water will evaporate too quickly when kept at a higher tempera-

ture. Thus, there would be a high risk of overheating when the water level falls below 

the minimum amount of 0,5 litres.

Note:

You may cancel the operating cycle at any time by removing the kettle from its 

base, or by pressing the ON/OFF button. Do not leave the kettle in keep warm 

operation needlessly to avoid useless energy loss.

SELECTING THE DESIRED TEMPERATURE  

The electronic »Design Kettle Cool Touch« can heat water to a selected temperature 

in the range from 35°C to 100°C (boiling temperature). The set temperature may be 

modified at any time during operation (heating up or keeping warm) or in standby 

mode. However, please keep in mind, that the actual water temperature could rise 

above the set temperature after heating. This will occur especially with a low tempe-

rature selected and/or only a small amount of water in the kettle. 
1.   Press the temperature selection buttons „KEEP WARM“ or „TEMP“ several times 

until the desired temperature is shown on the display. 

2.   If the kettle is in standby mode, press the ON/OFF button to start operation. If 

the kettle is in operation already, the thermostat of the kettle will automatically be 

adjusted to the newly set temperature.

SOLVING PROBLEMS

If any problems occur during operation, you will find the solution in the following 

table.  

Problem

Reason

The Solution

The display remains 

dark. No signal 

sounds, when pla-

cing the kettle on 

the base.

The appliance is not live. Ensure that the appliance is connected to a suitable 

wall power outlet. Ensure that the wall power outlet is 

live by connecting a lamp.
Check, if the kettle is connected correctly to the base. 

Turn it a little.

A severe problem  

occurred.

Immediately take the kettle off the base and unplug 

the base. Get in contact with an authorised service cen-

tre for examination and repair.

The kettle is placed 

on the base and 

plugged in, but the 

display is dark.

The automatic shut-off 

has been triggered.

If no button has been pressed for 30 minutes, the 

kettle will switch OFF completely to save energy. Simp-

ly press a button to reactivate the display.

The appliance is 

live, but the water 

is not heated.

The overheat protection 

system has been trig-

gered.

The kettle has been operated without water or with too 

little water. Empty the kettle and leave it cool down for 

at least 20 minutes. Thereafter, fill the kettle with at 

least 0.5 litres of cold water and try again.
Too much scale is covering the heating elements, cau-

sing overheating. De-scale the kettle (see: ‘De-scaling 

the Kettle’).

Water accumulates 

under the base or 

runs down on the 

exterior of the 

kettle.

There is too much water 

in the kettle.

Immediately unplug the appliance. Then wipe dry the 

appliance completely. Always observe the MAX filling 

level when filling (1.5 litres).

You spilled some water 

when filling or moving 

the kettle. 

Immediately unplug the appliance. Then wipe dry the 

appliance completely. Ensure not to spill water on the 

exterior of the kettle during filling. Always ensure to 

hold the kettle level when it is filled.

The kettle is leaking.

Immediately unplug the appliance and wipe dry the 

appliance completely. Then check the kettle for leaka-

ge. Do not use the appliance, if the kettle is leaking.

Summary of Contents for 62436












Reviews: