background image

Wall-mount type of Carbon Dioxide Detector 

Model: GTF220

 

GASTECH is a professional manufacturer in various gas detectors, carbon monoxide detector, carbon dioxide detector, 
oxygen detector, odor detector, VOC detector, hydrogen sulfide detector and carbon monoxide detector. Welcome tour 
our website 

www.gastech.com.tw 

4

 

M O D E L … A 0 3 

G T F 2 2 0 - A 

1. Power on display

 

After power on, the GTF220 carbon dioxide detector will display a series of messages, including welcome, model 

no and carbon dioxide concentration in ppm. 

 
WELCOME 
 

 

 

Show the model no. (Show it at power on only.) 
GTF220-A is a standard type with 4 ~ 20 mA analog output. 
GTF220-R is an optional type with relay output. 
 

 
It’s warming up now, please wait. (Show it at power on only.) 
 
 
 
Show the concentration of carbon dioxide. 
The measuring range would be 350 ppm to 8,000 ppm. 

It may shows >8,000 ppm while 

concentration of carbon dioxide is higher than above range. 

 
 

2. Settings 

The following operating procedure describes the settings. In the operation, press NEXT key or idle 3 minutes, the 
display will back to the concentration of carbon dioxide. 

 
In the display, press NEXT key to enter next function. 
 
 
 
In the display, press ADJ key, the buzzer and flash lamp will action. Press ADJ key again, 
they will stop. 

(The relay will make action in TEST ALARM also, if detector model has 

relay output.) 

Press NEXT key to enter next function. 
 
 
In the display, press ADJ key, to reset the buzzer high limit. The last words of last row 
might show UP, press ADJ key will increase the setting limit. Press UPDN key, the word 
will change to DN; press ADJ key will decrease the setting limit. 
Press NEXT key to enter next function. 
 
In the display, press ADJ key, to reset the buzzer low limit. The last words of last row might 
show UP, press ADJ key will increase the setting limit. Press UPDN key, the word will 
change to DN; press ADJ key will decrease the setting limit. 
Press NEXT key to enter next function. 
 

G A S T E C H 

W E L C O M E 

WARMING-UP 

WAIT…. 

CO

2  

364 ppm

 

TEST ALARM

 

Buzzer H. L. 

3500 ppm UP 

 

CO

2  

364 ppm 

Buzzer L. L. 

  350 ppm UP 

Summary of Contents for GTF220







Reviews: