Gasmate SOHO BQ1096, Manual, Page: 4 / 12

5 4
GENERAL ASSEMBLY
Connecting & Disconnecting to the Gas Source
Familiarise yourself with the general information and
safety guidelines located at the front of this manual.
Check
1. The cylinder is filled. A sloshing sound will be heard
when shaken.
2. The burner controls are in the ‘OFF’ position
Connecting
1. Ensure cylinder valve is in its full off position.
2. Check for any damage to either the cylinder
connection or the hose. NEVER attempt to use
damaged equipment.
3. When connecting the hose to the cylinder tighten the
nut to a positive stop by hand.
4. Open cylinder valve fully. If a leak can be heard at
either end of the hose turn cylinder off and tighten
joint. Wait 5 minutes before re-testing and use a
soapy water solution to check the joint. If bubbles
appear the connection will need to be re-tightened.
Disconnecting
1. Ensure the burner control is in the ‘OFF’ position.
2. Ensure cylinder valve is in the full off position.
For storage and cylinder exchange, disconnect hose
at the cylinder only, DO NOT disconnect hose from
appliance.
Disconnecting
1. Ensure the burner control is in the ‘OFF’ position.
2. Ensure cylinder valve is in the full off position.
FOR STORAGE AND CYLINDER EXCHANGE,
DISCONNECT HOSE AT THE CYLINDER ONLY, DO
NOT DISCONNECT HOSE FROM APPLIANCE.
LIGHTING PROCEDURE
Burner Operation & Ignition System Check
1. Open the hood of the barbecue before attempting to
light the burners.
2. Turn the control knobs clockwise to “OFF” position.
3. Connect the regulator to the gas bottle. Turn the gas
supply “ON” at the cylinder. Check with the use of
soapy water for any gas leakage between the bottle
and the regulator
4. Push down a control knob and keep pressing whilst
turning anti-clockwise to the “HIGH” position (a
clicking sound is heard), this will light the burner. If
the burner does not light, repeat this process.
5. If the burner still does not light, turn the control knob
to ‘OFF’ wait 5 minutes and repeat step 3.
6. Adjust the heat by turning the knob to the High/Low
position.
7. To turn the barbecue ‘OFF’, turn the cylinder valve
to the ‘OFF’ position and then turn all of the control
knobs on the appliance clockwise to the ‘OFF’
position.
Problem: Burner will not ignite
Possible Reason Solution
Valve on cylinder
is closed Open valve on cylinder
Control knob is off Turn knob to high when
lighting
Igniter is faulty Use a long barbecue match
Burner has gone out Check that the gas bottle
is not empty and re-ignite
the burner
Ignition System Check
IMPORTANT
• Do not smoke when attempting to ignite the
barbecue.
• Never use volcanic rock, heat beads or other
material.
• Always use protective gloves when handling hot
components.
• Note: If for some reason, ignitor fails to produce
a spark at the electrode, barbecue can be lit by a
long barbecue match. With the cover removed, lift
out the grill plate and light a burner with a match or
lighter. Subsequent burners will crosslight.
• The lid must be in the open position for lighting and
during use.
• Do not leave the barbecue unattended when alight.
• Clean your barbecue after each USE. DO NOT use
abrasive or flammable cleaners, as it will damage
the parts of the product and may start a fire. Clean
in warm soapy water.
• IMPORTANT: Before connecting and disconnecting
barbecue to gas source, make sure burner controls
are in ‘OFF’ position.
• CAUTION: When the barbecue is not in use, the gas
must be turned off at the cylinder
• Check that the seals between the appliance and
the gas cylinder are in place and in good condition
before connecting the gas cylinder
• Do not use this appliance if it has damaged or worn
seals.
• Check performance of burner prior to installing BBQ
plates.
REMOVE TRANSIT PACKAGING
MATERIAL BEFORE USE.