Gasmate BQ10622 Instructions Manual Download Page 3

3

2

GENERAL INFORMATION

Gas Installation Codes

•  Barbecues must be used in accordance with the  
  installation requirements of your gas supply authority,  
  or the Australian Standard AS 5601.
•  Barbecues for use with bottled gas are labelled  
  ‘propane gas’ or ‘Universal L.P.G’.
•  Barbecues for use with natural gas are labelled  
  ‘natural gas’ and must be installed by an authorised  
  person. Check the gas type sticker attached to the  
 barbecue.

Clearances

Minimum Clearances from combustible materials  
must be:  
Rear - 300mm    Sides - 300mm    Above - 1000mm 

Specifications

Barbecue specifications can be found on the data label 
attached to the barbecue body.
Hose connection thread is 5/8”-18 UNF.

 IMPORTANT

Read these instructions carefully prior to use. 
Familiarise yourself with the appliance before 
connecting it to it’s gas container. Keep these 
instructions for future reference.

 

IF YOU SMELL GAS 

1.   Shut off gas to the barbecue at its source,  

  if possible.

2.   Extinguish any open flame.
3.   Open hood.
4.   If odour continues immediately call your gas  

  supplier or fire department.

Hose & Regulator Safety

The regulator and hose assembly supplied with the 
barbecue are suitable for Propane Gas or Universal 
L.P.G. only. 
A gas regulator adjusted to have an outlet pressure of 
2.75kPa is supplied for connection to the propane gas 
cylinder. The pressure regulator and hose  assembly 
supplied with the barbecue must me used. Replacement 
pressure regulators and hose assemblies must be those 
specified by the barbecue manufacturer.
When connecting the hose and regulator assembly to the 
gas cylinder, take care to avoid unnecessary twisting of 
the flexible hose.
After the assembly has been secured, turn on the gas 
and check for leaks by brushing a soap and water 
solution over all connections. 
If you are unable to correct the leak by tightening the 
connections, turn off the gas and contact the supplier 
immediately.
Always ensure the barbecue is kept away from flammable 
materials and the gas cylinder clear of any heat source.
When changing over from an empty gas cylinder to a 
full one make sure this procedure is carried out in a well 
ventilated location, preferably outside, away from people 
and away from any sources of ignition; such as naked 
flames, pilot flames, electric heaters/equipment.

Gas Cylinder Use & Safety

While changing over empty gas cylinder check hose 
and regulator for damage and if necessary replace. 
Replacement pressure regulators and hose assemblies 
must be those specified by the barbecue manufacturer.
This is a low pressure barbecue and must only be used 
with the regulator supplied. Your barbecue is designed 
for use with 4.5Kg or 9Kg propane gas cylinders certified 
to AS 2469.
The gas cylinder should be filled by a reputable gas 
supplier and visually inspected and re-qualified at each 
filling.
Always keep cylinder in an upright position. Always close 
the cylinder valve when the barbecue is not in use.
Do not subject gas cylinder to excessive heat.

NEVER STORE YOUR GAS CYLINDER INDOORS.
If you store your barbecue indoors, ALWAYS disconnect 
the gas cylinder first and store the cylinder safely outside.
Cylinders must be stored outdoors in a well ventilated 
area out of reach of children, and must not be stored in a 
building, garage or any other enclosed area.

Summary of Contents for BQ10622

























Reviews: