background image

Blaze Outdoor Heater

Model No. GM124-028

FOR YOUR SAFETY

If you smell gas:

1.   Shut off the gas to the  

 

    appliance.

2.   Extinguish any open flame.

3.  If odour continues,    

 

    immediately call your gas
    supplier.

Do not store or use gasoline 
or other flammable vapour and 
liquids in the vicinity of this or any 
other appliance.

WARNING:

Improper installation, adjustment, 
alteration, service or maintenance 
can cause injury or property 
damage.

Read the instructions thoroughly 
before installing or servicing this 
equipment.

Important: The installer or seller must leave these instructions with the consumer.

IMPORTANT:

• 

  

Retain these instructions for future use.

4782-07/17

FOR OUTDOOR USE 

ONLY

OPERATES ON 

LPG/ULPG

•  The glass tube will be extremely  
  hot when it is working so never   
  try to touch it and keep children  
 away.

•  Turn off the appliance    

 

  immediately if it starts raining    
  and never use it while it is  

 

  raining as the glass tube may    
  break when it comes in contact   
  with water.

•  Never splash any liquid onto  

 

  the glass tube when the  

 

  appliance is on.

•  Always ensure the appliance  

 

  stands on a flat, firm surface as   
  the glass tube may break if the   
  appliance falls over.

•  Never use the appliance if the    
  glass tube has any cracks or  

 

 damage.

Summary of Contents for Blaze













Reviews: