background image

 18

OPERATION INSTRUCTIONS                                                                                               

Lighting Your Grill 

 

DANGER: Failure to open lid while igniting the grill or not waiting 5 minutes to allow 
the gas to clear if the grill does not light may result in an explosive flare-up which can 
cause serious bodily injury or death. 

 

Main Burners 

1.  Read ALL instructions before lighting. 
2.  Open lid before lighting. Make sure all BBQ control valves are in “OFF” position.   
3.  Open the LPG Cylinder Valve. 
4.  To ignite a burner, push and turn the burner control knob to HIGH. 
5.  Press the electronic ignitor and hold for 3 to 5 seconds to light the burner. 
6.  If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5minutes, and 

repeat the lighting procedure. 

7.  Follow same steps to light left and right main burners. 

 

After lighting, observe the burner flame and make sure all burner ports are lit. 
If burner flame goes out during operation, immediately turn the gas “off” on the grill and at 
the gas cylinder and open lid to let the gas clear for about 5 minutes before re-lighting. Clean 
your grill after each use. DO NOT use abrasive or flammable cleaners, as it will damage the 
parts of this product and may start a fire. 
 

Side Burner 

1.  Read ALL instructions before lighting. 
2.  Open lid prior to lighting. Lid must ALWAYS be open when side burner is operating. 
3.  Side burner valve must be in the “off” position. 
4.  Open the LPG cylinder valve. 
5.  To ignite the side burner, push and turn the side burner control knob to HIGH. 
6.  Press the electronic ignitor and hold for 3 to 5 seconds to light the burner. 
7.  If ignition does not occur in 5 seconds, immediately turn the side burner control off, wait 5 

minutes for the gas to clear and repeat the lighting procedure. 

8.  After burner ignites, adjust control knob to desired cooking setting. 

 

Shutting Off Burners: 

1.  Always turn the valve knob(s) clockwise to the High position, and then push in and turn 

to OFF. Never force the knob without depressing it as this can damage the valve. 

2.  Promptly turn the gas supply OFF at the LPG cylinder. 
3.  Close the lid of the grill. 
 
 
 

 

Summary of Contents for BG126N3B Toulon

























Reviews: