Garrard 401 Instruction Manual Download Page 21

spare parts list

20

The following items are also available, but not indicated on the diagram:-

71251/01

Turntable, with Mat and Centre Trim Disc (50 c/s)

71281/01

Turntable only (50 c/s)

71251/02

Turntable, with Mat and Centre Trim Disc (60 c/s) 

71281/02

Turntable only (60 c/s)

71689

Turntable Mat and Centre Trim Disc

59602/08

Adaptor, for large centre hole records, with Spring Clip

55743

Bottle of lubricating oil

72001

Studs, fixing Base Plate, with Spring Clips (4)

41058

Nuts, for Studs (4)

40678

Plain Washers, for Studs (4)

40962

Rubber Washers,for Studs (4)

71864

Resistor, for Neon Lamp Lead. 5,600 ohms 1/2 watt +

_ 10%

71980

Conversion Kit; from 50 c/s, 220/250 volts, to 60 c/s, 110/125 
volts, comprising Turntable, Motor Pulley and Neon Lamp.

71979

Conversion Kit; from 60 c/s, 110/125 volts, to 50 c/s, 220/250 
volts, comprising Turntable, Motor Pulley and Neon Lamp.

Note (from page 10)

If your unit is fitted with a neon lamp which ilIuminates
the stroboscopic turntable directly, the references to
the neon lamp and its housing made in this booklet are
not applicable.

If ever you require a lamp for your unit, lift it from its
location at the front of the unit sufficiently to note its
type number and quote this to our Spares Department.
Fitting instructions are supplied with the new lamp.

Summary of Contents for 401






















Reviews: