background image

Specifications

Specification

Measurement

Dimensions (H x W x D)

186 x 190 x 264 mm (7.61 x 7.48 x 10.39 in.)

Weight

5.6 kg (12.25 lb.)

Temperature range

From -15° to 55°C (from 5° to 131°F )

Material

• Electronics control unit (ECU): Fully gasketed aluminum alloy
• Bracket: Carbon steel
• Manifold: Aluminum alloy
• Motor: Aluminum alloy

Power cable length

2.7 m (9 ft.)

Input voltage 

From 10 to 30 Vdc

Fuse

40 A, blade-type

Main power usage

• Standby: Less than 1 A
• Engaged: From 5 to 10 A
• Peak threshold: 30 A

Port and Fitting Specifications

Port, Fitting, or Plug

Specification

H1 and H2 ports (top of manifold)

SAE ORB-5 (2)

C1 and C2 ports (side of manifold)

SAE ORB-5 (2)

T ports (side of manifold)

SAE ORB-5 (2)

Included fittings for H and C ports

SAE ORB-5 to 

1

/

4

 in. NPT straight (2)

Included fittings for T ports

SAE ORB-5 to 

1

/

4

 in. NPT elbow (1)

Included plugs for unused ports

SAE ORB-5 (3)

NOTE: Hose fittings must be purchased separately, if needed, to adapt from NPT to the hose type for each 
installation. For example, most SeaStar

 installations require SeaStar HF5528 or Parker

SM

 68C-6-4 fittings. Most 

Uflex and Verado

®

 installs require Parker 4-4 FLO. Also, the included adapters can be removed to adapt directly 

to SeaStar HF6009 or Verado 4-5 F5OLO hose fittings.

© 2017 Garmin Ltd. or its subsidiaries
Garmin

®

 and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Shadow Drive

 is a trademark of Garmin Ltd. 

or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
Loctite

®

 is a trademark of Henkel Corporation in the U.S. and elsewhere. NMEA 2000

®

 is a trademark of the National Marine Electronics Association.Parker

SM

 Parker is a 

service mark of Parker Intangibles, LLC. SeaStar

 SeaStar is a trademark of the Marine Acquisition Corp. Teflon

®

 is a trademark of DuPont

. Uflex

®

 and MasterDrive

 are 

trademarks of the UltraFlex Group. Verado

®

 is a trademark of Brunswick Corporation.

© 2017 Garmin Ltd. or its subsidiaries

support.garmin.com

Summary of Contents for Smartpump













Reviews: