PANOPTIX
™
LIVESCOPE
™
ICE
FISHING KIT
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
See the
Important Safety and Product Information
guide in the
chartplotter or fishfinder product box for product warnings and
other important information.
To obtain best performance and to avoid possible damage, you
must install this mount using these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation, go
for more information.
Battery Warnings
WARNING
The Garmin
®
device uses a user-replaceable, sealed, lead-acid
battery. If these guidelines are not followed, the battery may
experience a shortened life span or may present a risk of
damage to the device, fire, chemical burn, electrolyte leak,
and/or bodily injury.
• Do not place the battery near objects that may cause sparks,
flames, or heat.
• Do not incinerate the battery.
• Do not use a sharp object to remove the battery.
• Do not disassemble, puncture, or damage the battery.
• Do not swallow, touch, or inhale the contents of an open
battery. Avoid contact with internal acid. Contact with internal
acid may cause irritation or severe burns. Irritation may occur
to the eyes, respiratory system, and skin. Flush with water at
once if contact is made with acid.
• Do not submerge the battery and avoid contact with water.
• Do not short the battery terminals.
• Do not drop or throw the battery.
• Keep the battery away from children.
• Only replace the battery with the correct replacement battery.
Using another battery presents a risk of fire or explosion of
the device or charger.
• Only charge the battery with the included charger.
• Do not charge the battery in an unventilated area.
• Store in a cool, dry, and well-ventilated area.
• Do not charge the battery in a gas-tight container.
• Do not leave the device exposed to a heat source or in a
high-temperature location, such as in the sun in an
unattended vehicle. To prevent damage, remove the device
from the vehicle or store it out of direct sunlight.
• Do not use organic solvents or other cleaners other than
recommended chemical cleaners on the battery.
• Contact your local waste disposal department to dispose of
the battery in accordance with applicable local laws and
regulations.
• When storing the battery for an extended time, store within
the following temperature range: from 5° F to 104°F (from
-15° C to 40° C).
• Do not operate the battery outside of the following
temperature range: from 5° F to 122° F (from -15° C to 50°
C).
Attaching the Bail Mount
You need a Phillips screwdriver to attach the bail mount to the
portable mount.
1
Align the chartplotter bail mount over the hole pattern that
matches your bail mount, with the openings on the top of the
bail mount facing the back of the base.
2
Secure the bail mount to the base using the four included 24
mm machine screws and the included washers, if you are
installing a metal bail mount.
NOTICE
Only use the included washers if you are installing a metal
bail mount. If you are installing a plastic bail mount, do not
use the four included washers.
NOTE:
Do not use the self-threading screws included with
the chartplotter. Only use the machine-threaded screws
included with this portable kit or use M4 machine screws.
3
Place the included rubber washers on the bail-mount
knobs , and screw the knobs into the sides of the cradle or
chartplotter.
4
Place the cradle or chartplotter into the bail mount, with the
rubber washers between the knobs and the cradle or
chartplotter, and tighten the knobs.
The rubber washers enable you to adjust the viewing angle
without adjusting the knobs.
Assembling the Panoptix Ice Fishing Mount
You need a Phillips screwdriver and the included 5 mm hex
wrench to assemble the ice fishing mount and attach the
transducer.
1
Insert the Phillips head sheet metal screws into the four
corners of the ice mount base.
The screws protrude from the bottom of the base to help
stabilize the mount when it is on the ice.
2
Locate the handle and the top pole segment.
3
Place the base between the handle and the top pole ,
and screw them together.
GUID-2A0F406E-7D25-4B0C-B287-B0054C5B6EE7 v1
July 2020
