background image

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 
this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency 
energy and may cause harmful interference to radio communications if not installed and used in accordance 
with the instructions. However, there is no guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the 
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This product does not contain any user-serviceable parts. Repairs should only be made by an authorized 
Garmin service center. Unauthorized repairs or modifications could result in permanent damage to the 
equipment, and void your warranty and your authority to operate this device under Part 15 regulations.

Limited Warranty

The Garmin standard limited warranty applies to this accessory. For more information, go to 

www.garmin.com

/support/warranty

.

物質宣言

部件名称

有毒有害物

或元素

六价

多溴

多溴二苯

印刷

路板

X

O

O

O

O

O

金属零件

X

O

O

O

O

O

电缆

  

电缆组

  

接器

X

O

O

O

O

O

本表格依据

SJ/T11364

制。

O: 

代表此种部件的所有均

材料中所含的

种有害物

均低于

(GB/T26572) 

定的限量

X: 

代表此种部件所用的均

材料中

至少有一

材料其所含的有害物

高于

(GB/T26572) 

定的限量

*

明書應提供在環保使用期限和特殊標記的部分詳細講解

品的擔保使用條件。

連絡地址

製造銷售

:

台灣國際航電股份有限公司

聯絡地址

:

新北市汐止區樟樹二路

68

電  話

:(02)2642-8999

客服專線

:(02)2642-9199

© 2021 Garmin Ltd. or its subsidiaries
Garmin

®

 and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the 

express permission of Garmin.
MSC

 is a trademark of Garmin. This trademark may not be used without the express permission of Garmin.

NMEA 2000

®

 and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association.

13

Summary of Contents for MSC 10















Reviews: