Garmin GTX 35R Installation Manual Download | Manualshive

Page: 25 / 69

background image

190-01499-10

GTX 35R/45R Installation Manual (Non-Certified Aircraft)

Rev. 1

Page 3-3

3.5

Necessary Installation Materials and Accessories Not Supplied

The GTX 35R/45R is installed with standard aviation materials. The following items are necessary for
installation, but not supplied.

•

Wire (MIL-W-22759/16 or equivalent)

•

Shielded wire (MIL-C-27500 or equivalent)

•

Aircraft grade category 5 Ethernet cable or MIL-27500 shielded twisted-pair cable is necessary for
installations utilizing the HSDB interfaces (GTX 45R to GTN and/or GTS installations only)

•

Mounting hardware

•

Circuit breaker of applicable rating

•

Tie wraps and/or lacing cord

•

Ring terminals for grounding

•

Coaxial cable (RG-400 or equivalent)

•

Coax connectors – BNC connectors for the transponder antenna

3.6

Necessary Special Tools

NOTE

Insertion/extraction tools from ITT Cannon are all plastic. The others are plastic with
metal tips.

Some connectors use crimp contacts. Use crimp tools in table 3-3 to make sure reliable crimp contact
connections for the rear D-sub connectors are correct.

Table 3-3 Recommended Crimp Tools

Manufacturer

Hand Crimping Tool

22-28 AWG (P3251, P3252)

Positioner

Insertion/Extraction

Tool

Military PN

M22520/2-01

M22520/2-09

M81969/14-01
M81969/1-04

Positronic

9507-0-0-0

9502-4-0-0

M81969/1-04

ITT Cannon

995-0001-584

995-0001-739

000849490
274-7048-000MIL

AMP

601966-1

601966-6

91067-1
2031838-1

Daniels

AFM8

K42

M81969/14-01
M81969/1-04

Astro

615717

615725

M81969/14-01
M81969/1-04

«
...
23
24
25
26
27
...
»

Summary of Contents for GTX 35R






































































Reviews:

No comments

Related manuals for GTX 35R

Brand: Dexford Pages: 4

Brand: Philco Pages: 7

Brand: Salora Pages: 21

Brand: Radio Shack Pages: 12

Brand: Simoco Pages: 2

Brand: Cassidian Pages: 88

Brand: GPX Pages: 4

Brand: Teac Pages: 24

Brand: Destination Audio Pages: 12

Brand: Sangean Pages: 69

Brand: Siemens Pages: 7

Brand: Siemens Pages: 2

SIMATIC RTLS4060T

Brand: Siemens Pages: 13

Brand: Siemens Pages: 4

Brand: Siemens Pages: 6

SIMATIC 6GT2700-6DE03

Brand: Siemens Pages: 21

SIMATIC RTLS4083T

Brand: Siemens Pages: 33

SIMATIC RTLS4084T

Brand: Siemens Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands