manualshive.com logo in svg

Garmin GTN 6 series, Maintenance Manual, Page: 68 / 163

Share
Download
Garmin GTN 6 series Maintenance Manual Download Page 68

190-01007-C1

GTN Xi Part 23 AML STC Maintenance Manual

Rev. 1

Page 5-18

5.3.1.8 Datalink Related Alerts

Table 5-10  Datalink Alert Troubleshooting Guide

Alert Text

Possible Cause

Corrective Action

DATALINK - FIS-B weather has 

failed.

The FIS-B receiver is reporting 

that it has failed. The display of 

FIS-B products may be 

unavailable.

Check wiring to ADS-B In 

source. Check for internal faults 

in the ADS-B equipment. If 

problem persists, contact 

Garmin technical support for 

service.

DATALINK – GDL 69 is 

inoperative or connection to 

GTN is lost.

The GTN Xi cannot 

communicate with the GDL 69.

Check for proper configuration.
Ensure the GDL 69 is powered 

up.
Verify that the GDL 69 Ethernet 

ports are enabled. 
HSDB data from the GDL 69 can 

be routed to the GTN Xi through 

other Garmin LRUs. Ensure that 

all Garmin LRUs are powered 

up.

DATALINK – GDL 88 is 

inoperative or connection to 

GTN is lost.

The GTN Xi cannot 

communicate with the GDL 88.

Check for proper configuration.
Ensure the GDL 88 is powered 

up.
HSDB data from the GDL 69 can 

be routed to the GTN Xi through 

other Garmin LRUs. Ensure that 

all Garmin LRUs are powered 

up.

DATALINK - GDL 88 ADS-B 

failure. Unable to transmit ADS-

B messages.

GDL 88 is not able to transmit 

an ADS-B message due to a 

failure with the GDL 88 system 

or antenna(s).

Check the 

GDL 88 Fault

 page in 

Configuration mode on the 

GTN Xi.
Refer to the GDL 88 STC 

Installation Manual.

DATALINK – GDL 88 ADS-B 

fault.

The GDL 88 has detected a fault 

with one of the GDL 88 UAT/

1090 antennas.

Refer to the GDL 88 STC 

Installation Manual.

DATALINK – ADS-B fault: UAT 

receiver.

The GDL 88 has detected a UAT 

receiver fault.

Refer to the GDL 88 STC 

Installation Manual.

DATALINK – ADS-B fault: 1090 

receiver.

The GDL 88 has detected a 

1090 receiver fault.

Refer to the GDL 88 STC 

Installation Manual.

DATALINK - GDL 88 ADS-B is 

not transmitting position. Check 

GPS devices.

The GDL 88 has detected a 

position input fault.

Refer to the GDL 88 STC 

Installation Manual.

DATALINK - GDL 88 control 

panel input fault. Check 

transponder is in correct mode.

The GDL 88 has lost 

communication with the 

transponder.

Refer to the GDL 88 STC 

Installation Manual.

Summary of Contents for GTN 6 series




































































































































































Reviews:

No comments