Garmin GPS 175 Maintenance Manual Download Page 82 | Manualshive

Page: 82 / 95

Garmin GPS 175 Maintenance Manual Download Page 82

190-02207-A2

GPS 175/GNX 375/GNC 355 Part 23 AML STC Maintenance Manual

Rev. 3

Page 7-2

7.1 Software Check

To check the GPS 175/GNX 375/GNC 355 software version:

1. Power on the GPS 175/GNX 375/GNC 355 in Configuration mode by holding down the inner

knob and pressing the

Power/Home

key.

2. Touch the

System Information

button.

3. Observe the installed software version and part number and verify that the version number and part

number matches the approved version listed in the Equipment List.

7.2 Software Updates

Touch the

System Information

button to determine the current software loaded to the unit. Refer to the

GPS 175/GNX 375/GNC 355 Part 23 AML Equipment List

(P/N 005-01206-A2) for the current approved

software for this STC. If the software needs to be updated, a software loader card will need to be created to

update the software. An SD card, SD card reader, and a PC running Windows 2000, XP, Vista, Windows 7,

Windows 8, or Windows 10 are necessary. There is no Mac support currently.

7.2.1 Software Loader Card Instructions

To create a software loader card, perform the following steps:

1. Log in to the Garmin

Dealer Resource Center

2. Download the appropriate system software to a PC.
3. Connect an SD card reader to the PC.
4. Insert the SD card into the card reader.
5. Run the *.exe file downloaded from the Dealer Resource Center.
6. Follow the screen prompts to create the loader card.
7. Click the

Finish

button.

8. Eject the loader card.

7.2.2 Software Update Instructions

To update the GPS 175/GNX 375/GNC 355 software, perform the following steps:

1. Power off the unit.
2. Remove the database card and insert the correct GPS 175/GNX 375/GNC 355 software loader

card into the data card slot. Refer to Section 7.2.1 for creating a software loader card.

3. Power on the unit.
4. The GPS 175/GNX 375/GNC 355 will power on in Configuration mode. Touch the

Updates

button to display the available software updates.

5. Verify that the software version being loaded to the GPS 175/GNX 375/GNC 355 matches the

software version listed in

GPS 175/GNX 375/GNC 355 Part 23 AML STC Equipment List

. The

Updates

page displays the software version that is currently installed on the unit and the software

version on the loader card.

6. Touch the software versions or packages to select them for updating. To update the GPS 175/

GNX 375/GNC 355 with all available software, touch the

Select All

button in the upper-right

corner of the display.

7. To begin the software update, touch the

Update

button in the lower-right corner of the display.

8. When the updates are complete, power off the unit and re-insert the database card.

«
...
80
81
82
83
84
...
»

Summary of Contents for GPS 175
































































































Reviews:

No comments