background image

Installation Troubleshooting

Symptom

Possible Causes

The radar does not turn 
on. The status LED is not 
on.

• The power cable may not be connected correctly to the device or to the battery. 

Check all connections.

• The inline fuse may have blown. Check the fuse and replace it if necessary.
• The wire gauge used to extend the power cable may be too small for the length 

of the extension. Check the table provided in the Power Cable Extensions section 
of these instructions to make sure the correct wire gauge is used (

Power Cable 

Extensions, page 9

).

The radar is not available 
on the Garmin device 
or on devices connected 
to the Garmin Marine 
Network.

• The radar may not be powering on. Check the status LED.
• The device software may not be up-to-date. Update the software on the device or 

on the Garmin Marine Network.

• The network cable may not be connected correctly to the device or to the Garmin 

Marine Network. Check all connections.

• If a field-installable network connector was used, it may have been installed 

improperly. Check the connector.

The status LED is located on the product label, and can help troubleshoot installation problems.

Status LED Color and Activity Radar Status

Solid red

The radar is getting ready for use. The LED should be solid red briefly and 
change to flashing green.

Flashing green

The radar is operating properly.

Flashing orange

The radar software is being updated.

Flashing red

The radar has encountered an error. Contact Garmin product support for assis­
tance.

Contacting Garmin Support

• Go to 

support.garmin.com

 for help and information, such as product manuals, frequently asked questions, 

videos, and customer support.

• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.

© 2018 Garmin Ltd. or its subsidiaries
Garmin

®

 and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GMR

, Fantom

, and MotionScope

 are 

trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

© 2018 Garmin Ltd. or its subsidiaries

support.garmin.com

Summary of Contents for GMR FANTOM OPEN ARRAY Series



















Reviews: