background image

GHP 20 Installation Instructions 

19

GHP 20 Installation Checklist

Detach this checklist from the installation instructions and use it to assist with the GHP 20 installation process.
Read all installation instructions before installing the GHP 20. Contact Garmin Product Support if you have any questions during the installation 

process.

 

1. Refer to the diagram and notes starting on 

page 6

 to understand the necessary electrical and data connections.

 

2. Lay out all of the components first. Check the cable lengths. Obtain extensions if necessary.

 

3.  Mount the CCU by following the directions starting on 

page 5

. Mount the CCU in a location free of magnetic interference. Use a 

handheld compass to test for magnetic interference in the area. 

Mount the CCU in the bracket so that the wires hang straight 

down

.

 

4.  Mount the GHC 10 by following the directions starting on 

page 5

.

 

5. Connect the CCU to the steering system of the boat using the steering controller cable (

page 7).

 

6.  Connect the GHC 10 and the CCU to a NMEA 2000 network. Connect an optional NMEA 2000-compatible GPS device to the NMEA 

2000 network (

page 8).

 

7.   Connect an optional NMEA 0183-compatible GPS device to the GHC 10 if a NMEA 2000-compatible GPS device is not available 

(

page 10

).

 

8. Configure the GHP 20 system (

page 11

).

CCu Mounting template

Up, when installing on a 

vertical surface

Summary of Contents for GHP 20





















Reviews: