background image

Settings

GHC 10 Owner’s Manual 

17

Configuring the gHC 10 remote

1.  From the Heading screen, select 

Menu

 > 

Setup 

Remote

.

2.  Select an option:

• 

Button 1 Action

—set the function performed by the first button on 

the remote.

• 

Button 2 Action

—set the function performed by the second button 

on the remote.

• 

Button 3 Action

—set the function performed by the third button on 

the remote.

• 

Disconnect Remote

—disconnect the remote from the device.

gHC 10 User settings

 CaUTIOn

On a GHP 10 autopilot system, if you disable the Shadow Drive, you must 

set the autopilot to standby (

STBY

) to manually control the helm. Use 

caution when disabling the Shadow Drive.
On a GHP 10V autopilot system, if you disable the Shadow Drive, any 

adjustment to the helm completely disengages the autopilot.
Although the autopilot is configured for your boat during installation, you 

may find it necessary to adjust it depending on sea conditions.
Select 

Menu

 > 

Setup 

User Autopilot Configuration

.

• 

Shadow Drive

—enables the device to enter standby mode 

automatically when you manually steer the helm, then engages the 

heading hold again when you hold a steady course for a few seconds. 
NOTE: The Shadow Drive is only available on hydraulic steering 

systems.

• 

Shadow Drive Sensitivity

—Shadow Drive is activated when a certain 

amount of pressure is placed on the helm. Adjust this setting if the 

Shadow Drive is being falsely tripped or not activating properly. If the 

autopilot disengages while the helm is steady, decreasing the sensitivity 

value can help alleviate unwanted disengaging. If the Shadow Drive does 

not disengage the autopilot correctly when you take the helm, increasing 

the sensitivity value may help. 

NoTe:

 This setting does not apply to a GHP 10V or GHP 12 autopilot 

system

.

• 

Sea State Filtering

—adjust the sea state filtering to set the heading 

responsiveness. Set sea state filtering to 0% under normal operating 

conditions. Increase sea state filtering in choppy conditions at low speeds 

to reduce rudder activity and reduce wear on the autopilot system.

• 

Direction Control

—enable the device to set the drive direction to 

forward or reverse from the heading screen when the autopilot is in 

standby mode. See 

page 4

 for information about 

using

 direction control.

• 

Heading Hold Tack Angle

—(sailboats only) set the fixed angle at 

which the autopilot performs a tack or gybe maneuver with heading hold 

engaged. Select an angle from 1° to 180°.

• 

Tack/Gybe Delay

—(sailboats only) the autopilot delays steering a tack 

or gybe after you initiate the maneuver using the remote or the device. 

The delay counts down on the heading screen, and sounds an alarm when 

the autopilot begins the tack or gybe. Select a delay from 0 to 15 seconds.

• 

Gybe Inhibitor

—(sailboats only) prevents the autopilot from performing 

a gybe. The gybe inhibitor does not prevent you from manually 

performing a gybe using the helm or step steering.

Summary of Contents for GHP 10V





























Reviews: