background image

Port Identification

Item

Description

Connects the stereo to the wiring harness for line and subwoofer outputs for zones 3 and 
4.

Connects the stereo to the wiring harness for auxiliary input 1, and for the line and 
subwoofer outputs for zones 1 and 2.

Connects the stereo to the power and speaker wiring harness for all zones.

FUSE

Contains the 15 A fuse for the device.

USB

Connects the stereo to a USB source.

SXM TUNER

Connects the stereo to a SiriusXM

®

 Connect Tuner to receive SiriusXM stations where 

available (not included).
Connects to a Fusion DAB module to receive DAB stations where available (not included).

DIGITAL AUDIO IN 
(OPTICAL)

Connects the stereo to an optical digital audio source, such as TV or DVD player.

ETHERNET

Connects the stereo to another Fusion PartyBus stereo, zone stereo, or network (

Fusion 

PartyBus Networking, page 12

).

ANTENNA

Connects the stereo to a typical AM/FM antenna.
If you are installing the stereo on a boat with a metal hull, you must use a ground-
dependent antenna. If you are installing the stereo on a boat with a non-metal hull, you 
must use a ground-independent antenna. See the installation instructions provided with 
your antenna for more information.

NMEA 2000

Connects the stereo to a NMEA 2000 network (

NMEA 2000 System Wiring Diagram

page 11

).

Connects to an NRX series remote control directly.

3

Summary of Contents for FUSION APOLLO MS-WB675



















Reviews: