background image

Fusion PartyBus Networking

The Fusion PartyBus networking feature allows you to connect multiple compatible stereos together on a 
network, using a combination of wired or wireless connections.
You can group a compatible stereo, such as the Apollo WB670 stereo, with other compatible stereos connected 
to the network. Grouped stereos can share available sources and control media playback on all of the stereos 
in the group, which allows for a synchronized audio experience across the vessel. You can quickly create, edit, 
and break up groups as needed from any compatible stereo or remote control on the network.
NOTE: A zone stereo, such as the Apollo SRX400, can create or join a group to control and play sources from 
other stereos, but it cannot share its sources with the group.
For additional considerations when sharing sources, see the owner's manual.
You can use compatible stereos and remote controls, whether they are grouped or not, to adjust the volume of 
the available speaker zones for any stereo on the network.

Wired Networking Considerations

When you are planning your network installation, observe the following considerations for all wired 
connections.
• You must connect devices using standard Cat5e or Cat6 network cables with RJ45 connectors.
• You can use one network cable to directly connect two compatible devices.
• You must use wired network switches and wired or wireless network routers when you connect more than 

two compatible devices to a network.

• If you install a router on the network, it should be configured to be a DHCP server by default. See your router 

instructions for more information.

• If you do not install a router, and there are no other DHCP servers on the network, you should configure one 

Fusion PartyBus stereo to be a DHCP server.

Wired Network Example for Direct Connections

No network setting changes are needed when connecting two devices together directly.

Fusion PartyBus zone stereo or remote control

Apollo MS-WB670 stereo

Fusion PartyBus stereo

12

Apollo MS-WB670 Installation Instructions

Summary of Contents for FUSION Apollo MS-WB670



















Reviews: