Time Zone
: Sets the time zone, or allows automatic selection
based on GPS location.
Navigation Settings
NOTE:
Some settings and options require additional charts or
hardware.
Select
Settings
>
Navigation
.
Route Labels
: Sets the type of labels shown with route turns on
the map.
Auto Guidance
: Sets the parameters the chartplotter uses
when calculating an Auto Guidance path, when you are using
some premium maps.
Turn Transition Activ.
: Sets the turn transition to be calculated
based on time or distance.
Turn Transition Time
: Sets how many minutes before the turn
that you transition to it as the next leg, when Time is selected
for the Turn Transition Activ. setting. You can raise this value
to help improve the accuracy of the autopilot when navigating
a route or an Auto Guidance path with many frequent turns or
at higher speeds. For straighter routes or slower speeds,
lowering this value can improve autopilot accuracy.
Turn Transition Dist.
: Sets how far before the turn that you
transition to it as the next leg, when Distance is selected for
the Turn Transition Activ. setting. You can raise this value to
help improve the accuracy of the autopilot when navigating a
route or an Auto Guidance path with many frequent turns or
at higher speeds. For straighter routes or slower speeds,
lowering this value can improve autopilot accuracy.
Route Start
: Selects a starting point for route navigation.
Other Vessel Settings
When your compatible chartplotter is connected to an AIS
device or VHF radio, you can set up how other vessels are
displayed on the chartplotter.
Select
Settings
>
Other Vessels
.
AIS
: Enables and disables AIS signal reception.
DSC
: Enables and disables digital selective calling (DSC).
AIS Alarm
Enabling AIS Transmission Test
).
Restoring the Original Chartplotter Factory
Settings
NOTE:
This affects all devices on the network.
1
Select
Settings
>
System
>
System Information
>
Reset
.
2
Select an option:
• To reset the device settings to the factory default values,
select
Reset Settings
. This restores the default
configuration settings, but does not remove saved user
data, maps, or software updates.
• To clear saved data, such as waypoints and routes, select
Clear User Data
. This does not affect maps or software
updates.
• To clear saved data and reset device settings to the
factory default values, disconnect the chartplotter from the
Garmin Marine Network, and select
Delete Data and
Reset Settings
. This does not affect maps or software
updates.
Sharing and Managing User Data
WARNING
This feature allows you to import data from other devices that
may have been generated by third parties. Garmin makes no
representations about the accuracy, completeness, or timeliness
of data that is generated by third parties. Any reliance on or use
of such data is at your own risk.
You can share user data between compatible devices. User
data includes waypoints, saved tracks, routes, and boundaries.
• You can share and manage user data using a memory card.
You must have a memory card installed in the device. This
device supports up to a 32 GB memory card, formatted to
FAT32.
• You can share data if two compatible devices are connected
using the blue and brown wires on the power cable or using
the User Data Sharing Cable (
).
Connecting to a Garmin Device to Share
User Data
NOTE:
This feature is not available on ECHOMAP UHD 70/90
devices. The blue and brown wires on those devices can
connect to NMEA 0183 devices only.
You can connect the ECHOMAP UHD 60 device to a compatible
Garmin device to share user data, such as waypoints. If the
devices are mounted near each other, you can connect the blue
and brown wires. If the devices are mounted too far apart for the
wires to reach, you can connect the devices using a User Data
Sharing Cable (010-12234-06).
1
Make sure both devices are connected to the same ground.
2
Complete an action:
• If the devices are mounted near each other, connect the
blue wire from the first device to the brown wire of the
second, and connect the brown wire from the first device
to the blue wire of the second.
• If the devices are not mounted near each other, obtain a
User Data Sharing Cable (010-12234-06), and connect
the devices following the instructions included with the
cable (
User Data Sharing Cable Wiring Diagram
).
3
On both devices, select
Nav Info
>
Manage Data
>
User
Data Sharing
.
User data is shared between the connected devices. If you
select Clear User Data, data is removed from both connected
devices.
User Data Sharing Cable Wiring Diagram
First device
User data cable
Second device
Item
Wire Function
Wire Color
Data
Blue
Data
Brown
Ground
Black
Data
Green
Data
White
Sharing and Managing User Data
41
Summary of Contents for ECHOMAP UHD
Page 1: ...ECHOMAP UHD Owner sManual...
Page 6: ......