Map Layers
: Sets the data that appears on the map page
(
).
Audible Driver Alerts
: Enables an audible alert for each type of
driver alert (
Driver Awareness Features and Alerts
).
Auto Zoom
: Automatically selects the zoom level for optimal
use of your map. When disabled, you must zoom in or out
manually.
myMaps
: Sets which installed maps the device uses.
Enabling Maps
You can enable map products installed on your device.
TIP:
To purchase additional map products, go to
1
Select
Settings
>
Map & Vehicle
>
myMaps
.
2
Select a map.
Navigation Settings
Select
Settings
>
Navigation
.
Route Preview
: Shows a preview of the major roads in your
route when you start navigation.
Calculation Mode
: Sets the route calculation method.
Fatigue Warning
: Alerts you when you have been driving for a
long period without a break.
Avoidances
: Sets road features to avoid on a route.
Custom Avoidances
: Allows you to avoid specific roads or
areas.
Environmental Zones
: Sets the avoidance preferences for
areas with environmental or emissions restrictions that may
apply to your vehicle.
Toll Roads
: Sets preferences for avoiding toll roads.
Tolls and Fees
: Sets preferences for avoiding toll roads and toll
stickers.
NOTE:
This feature is not available in all areas.
Restricted Mode
: Disables all functions that require significant
operator attention and could become a distraction while
driving.
GPS Simulator
: Stops the device from receiving a GPS signal,
and saves battery power.
Calculation Mode Settings
Select
Settings
>
Navigation
>
Calculation Mode
.
The route calculation is based on road speeds and vehicle
acceleration data for a given route.
Faster Time
: Calculates routes that are faster to drive but can
be longer in distance.
Shorter Distance
: Calculates routes that are shorter in distance
but can take more time to drive.
Off Road
: Calculates a direct line from your location to your
destination.
Setting a Simulated Location
If you are indoors or not receiving satellite signals, you can use
the GPS to set a simulated location.
1
Select
Settings
>
Navigation
>
GPS Simulator
.
2
From the main menu, select
View Map
.
3
Tap the map twice to select an area.
The address of the location appears at the bottom of the
screen.
4
Select the location description.
5
Select
Set Location
.
Camera Settings
Select
Settings
>
Camera
.
Garmin Real Vision™
: Displays a camera view when
approaching some destinations (
).
Forward Collision Warning
: Alerts you when the device
detects you are following too closely to the vehicle in front of
you (
Forward Collision Warning System
).
Forward Collision Sensitivity
: Allows you to set the sensitivity
of the forward collision warning. A higher sensitivity alerts you
sooner than a lower sensitivity.
Lane Departure Warning
: Alerts you when the device detects
you may be crossing a lane boundary unintentionally (
).
Camera Placement
: Allows you to indicate the placement of
your device in the vehicle.
Go Alert
: Alerts you when stopped traffic starts moving (
).
Record on Startup
: Enables the dash camera to start recording
video automatically when you turn on the device.
Automatic Incident Detection
: Saves video automatically when
the device detects a possible driving incident.
Data Overlay
: Includes date, time, location, and speed
information in the recorded video.
Video Resolution
: Sets the resolution and quality for video
recordings.
Record After Power Loss
: Continues recording video up to a
selected time period after external power is lost.
Backup Camera Settings
The backup camera settings allow you to manage paired
Garmin backup cameras and camera settings. This menu
appears on your navigation device only when the device is
connected to a wireless camera receiver cable. See the owner's
manual for your backup camera for detailed information about
pairing cameras and camera settings. Go to
to purchase a Garmin backup camera.
Select
Settings
>
Backup Camera
, and select a paired camera.
Unpair
: Removes the paired camera. You must pair the camera
again before you can view it using this device and cable.
Rename
: Allows you to rename the paired camera.
Guidance Lines
: Shows or hides guidance lines and allows you
to adjust the position of the guidance lines.
babyCam Settings
The babyCam settings allow you to manage paired Garmin
babyCam
™
cameras and camera settings. This menu appears
on your navigation device only when the device is connected to
a wireless camera receiver cable. See the owner's manual for
your camera for detailed information about pairing cameras and
camera settings. Go to
to purchase a
Garmin babyCam camera.
Select
Settings
>
babyCam
, and select a paired camera.
Power Settings
: Allows you to set the amount of time the video
appears on the screen.
Flip Video
: Allows you to flip or mirror the video.
Alignment
: Displays the babyCam video to help you align the
camera.
Check Seat Reminder
: Enables a reminder to check for rear
seat passengers before exiting the vehicle.
Unpair
: Removes the paired camera.
Rename
: Allows you to rename the paired camera.
Bluetooth Settings
Select
Settings
>
Bluetooth
.
Bluetooth
: Enables Bluetooth wireless technology.
18
Customizing the Device
