background image

 

400W Series 

190-01226-04 Rev. 2 

Instructions for Continued Airworthiness Bell 206B 

Page 22 of 22 

The latest revision of this document will be available through any Garmin dealer or from Garmin 
customer assistance.  A Garmin Service Bulletin, describing ICA revision, will be sent to dealers if 
revision is determined to be significant.   

2.16 Assistance 

FAA Flight Standards Inspectors or the certificate holder’s PMI have the required resources to respond 
to questions regarding this ICA. In addition, the customer may refer questions regarding this equipment 
and its installation to the manufacturer, Garmin. Garmin customer assistance may be contacted during 
normal business hours via telephone 913-397-8200 or email from the Garmin web site at 
www.garmin.com. 

2.17  Implementation and Record Keeping 

Modification of an rotorcraft by this Supplemental Type Certificate obligates the rotorcraft operator to 
include the maintenance information provided by this document in the operator’s rotorcraft maintenance 
manual and/or the operator’s rotorcraft scheduled maintenance program. 

3. AIRWORTHINESS LIMITATIONS 

There are no additional Airworthiness Limitations as defined in 14 CFR § 27, Appendix A. A27.4 that 
result from this modification. The Airworthiness Limitations section is FAA approved and specifies 
maintenance required under §§43.16 and 91.403 of the Federal Aviation Regulations unless an 
alternative program has been FAA approved.  

  

Summary of Contents for 400W Series























Reviews: