background image

4517957 Rev. 2 (06/05)

Page 1

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS OR LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE.

KEEP APPLIANCE AREA FREE AND CLEAR  

FROM COMBUSTIBLES.

WARNING:

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE CAN

CAUSE PROPERTY DAMAGE, INJURY OR DEATH.

READ THE INSTALLATION, OPERATION AND

MAINTENANCE INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR SERVICING  

THIS EQUIPMENT.

WARNING:

 ELECTRICAL GROUNDING INSTRUCTIONS

THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR PROTECTION 

AGAINST SHOCK HAZARD. IT SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED THREE-

PRONG RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG

INSTALLATION & OPERATING  

INSTRUCTIONS FOR THE 

GARLAND® STARFIRE SENTRY COMBINATION 

RANGE,

MODEL STW286A

DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR TO THIS APPLIANCE.
PLEASE READ ALL SECTIONS OF THIS MANUAL AND RETAIN FOR FUTURE REFERENCE.

THIS PRODUCT HAS BEEN CERTIFIED AS COMMERCIAL COOKING EQUIPMENT AND MUST BE INSTALLED BY 

PROFESSIONAL PERSONNEL AS SPECIFIED.

For Your Safety:

Post in a prominent location, instructions to be followed in the event the user smells gas.  

This information shall be obtained by consulting your local gas supplier.

Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent using genuine 

Garland replacement parts. Garland will have no obligation with respect to any product that has been improperly installed, 

adjusted, operated or not maintained in accordance with national and local codes or installation instructions provided 

with the product, or any product that has its serial number defaced, obliterated or removed, or which has been modified 

or repaired using unauthorized parts or by unauthorized service agents. For a list of authorized service agents, please refer 

to the Garland web site at http://www.garland-group.com. The information contained herein, (including design and parts 

specifications), may be superseded and is subject to change without notice.

Continuous product improvement is a Garland policy, therefore design and specifications are subject to change without notice.

GARLAND COMMERCIAL INDUSTRIES

185 East South Street

Freeland, Pennsylvania 18224

Phone: (570) 636-1000

Fax: (570) 636-3903

GARLAND COMMERCIAL RANGES, 
LTD.

1177 Kamato Road, Mississauga, Ontario L4W 1X4

CANADA

Phone: 905-624-0260

Fax: 905-624-5669

Enodis UK LTD.

Swallowfield Way, Hayes, Middlesex UB3 1DQ ENGLAND

Telephone: 081-561-0433

Fax: 081-848-0041

4517957 Rev. 2 (06/05)

© 2005 Garland Commercial Industries, Inc.

Summary of Contents for SRW286A

































Reviews: