Step 8 (optional)
Place the Self Watering Platform Insert inside the
flat based tray of the Grow Light Garden as shown
in Fig 7. Cover with the Capillary Matting Section,
dark side up, draping the excess over one end of
the Self Watering Platform Insert only. Place the 4
Growing Trays on top of the Capillary Matting.
To ‘self water’ your plants, pour water directly
into the flat based tray, ensuring that the excess
capillary matting is in direct contact with the
water. The capillary matting will naturally draw
water across its entire length. As long as
you ensure that the growing mix in your trays is
in direct contact with the capillary matting through
the 24 holes in the
base of each tray,
your plants will
in turn draw on
water by capillary
action – see Fig. 8.
Assembly Instructions
Assembly of this product should take in the
region of 30 minutes. The only tools you will
require will be a hammer, or preferably
rubber mallet, and a crosshead screwdriver.
Firstly please check the contents list on the
previous page to ensure that you have all
the required parts to complete the assembly.
Step 1 (refer to Fig. 1)
Place the curved canopy upside down on a flat sur-
face. Take a fixing bolt and slot it through one of the
holes of the canopy - the head of the bolt should
be on same face as the oval branding badge.
Slot a ballast clip over the exposed threaded
section of the fixing bolt and secure it in place by
threading a nut on to the bolt. Tighten so that the
mounting clip is securely held in position
against the exposed underside of the canopy.
Repeat for all 4 mounting clips.
Step 5 (refer to Fig. 5)
Insert each of the aluminium tubes into the two
slots in the flat base tray. Using a rubber mallet,
force the tube into the slot to achieve a firm fix.
If a rubber mallet is not available, use a regular
hammer but cushion the impact on the end
of the tube to prevent the tube profile from
becoming damaged.
Step 6 (refer to Fig. 5 & 6)
Insert the supplied steel black nuts into each of
the 2 Height Adjuster Clamps as shown. Slide
each of the Height Adjuster Clamps over each of
the exposed aluminium tubes and secure at the
desired height using the thumbscrews. Be
careful not to over tighten the thumbscrews
– a soft grip is all that is required. Now slide
the canopy section over the exposed tube
sections until it is supported by the Height
Adjuster Clamps. You can adjust the height of
the canopy as required. Finally using the plastic
plugs, cap each of the exposed tube sections.
Step 7
Connect the power cord to your electrical
supply. The unit is now ready for use.
Step 4 (refer to Fig. 4)
Locate each of the Grow Lights into position
by pushing them into the ballast clips. Do not
push directly on the light tubes themselves,
for fear of them breaking, rather exert the
pressure on the ballast holding each of the
tubes.
Step 2 (refer to Fig. 2 & 3)
Peel off the blue protective file from each
Nanotech reflector. Place each ballast on a flat
surface. Now remove each of the Grow Light
Tubes from the ballasts by rotating the tube
through 90 degrees to unlock it from the ballast.
Push each Nanotech reflector down on to the
ballast so that it clips into place along the full
length and is held firmly – a small amount of
force is required. Refit each of the Grow Light
Tubes by sliding the pins on the ends of the
Grow Light Tube into the ballast sockets and
then rotate through 90 degrees to lock into place.
Step 3
Before attempting to locate the Grow Lights
into position, connect the power cord into
the exposed sockets at one end of each of
the lights. Do not plug the power cord into
the mains supply yet.
Fig.7
Fig.4
Please note that use of
the self watering insert
and capillary matting is
optional and not essential
to healthy plant development.
Steel Black Nut
Height
Adjuster
Clamp
Thumbscrew
Fig. 4
Canopy
Plastic Plug
Flat Base Tray
Aluminium
Tube
Height Adjuster
Clamp
Fig. 3
Steel Black Nut
Height
Adjuster
Clamp
Thumbscrew
Fig. 4
Canopy
Plastic Plug
Flat Base Tray
Aluminium
Tube
Height Adjuster
Clamp
Fig. 3
Fig. 5
Ballast
Clip
Fig.2
Fig.1
Nut
Curved
Canopy
Ballast
Clip
Bolt
Nanotech
Reflector
Grow Light
Tube
Nanotech
Reflector
Fig. 6
Stage 1
Stage 2
Fig.8
Grow Light Tube
Nanotech
Reflector
Ballast
Pins
Slide Pins into
Socket
Rotate 90
o
until
Tube ‘locks’ into
place
Fig.3
Grow Light
Tube
Power Cord
