background image

Part # 1382636 Rev 5 (01/25/08)

Page 6

INSTALLATION

INTRODUCTION

Periodic inspections by your dealer or a qualified service 

agency are recommended . 

We suggest installation, maintenance and repairs should be 

performed by your local authorized service agency listed 

in your information manual pamphlet, or you may call the 

factory at 1-800-2-211 .

Rating Plate

When corresponding with the factory or your local 

authorized factory service center regarding service problems 

or replacement parts, be sure to refer to the particular unit 

by the correct model number (including the prefix and suffix 

letters and numbers) and the warranty serial number . The 

rating plate affixed to the unit contains this information .

Clearances

The clearance from combustibles on the AP1 & AP is six (6”) 

inches, (152mm) on the right and rear side and zero (0”) on 

the left . It is recommended that there be six (6”) (152 mm) of 

clearance on the right side for fuse panel access .

Location

Proper placement of the oven will ensure operator and 

satisfactory performance . Adequate clearance must be 

provided for servicing, ventilation (if applicable), and 

proper operation . The oven must be kept free and clear of 

combustible material .

WARNING  Control components may experience reduced 

life if exposed to high temperatures . We recommend not 

exposing control areas to temperatures above 10 degrees 

Fahrenheit for a continuous period of time . For this reason, 

care must be taken on installation to allow air flow around 

units, especially when placed near other heat producing 

sources . We recommend 6” (152 mm) spacing to the control 

side of oven from other heat producing sources .

Installation for Ovens Equipped with Legs

The AP1 counter unit is shipped with four () legs . This unit 

is stackable up to three (3) units . The AP1 is considered the 

base appliance and the APA is the stacking appliance .

WARNING:  The base of counter appliance must be installed 

with minimum ” legs . The base appliance needs air 

flow from the bottom for proper operation and is a NSF 

requirement .

CAUTION:  DO NOT LAY UNIT ON SIDES OR TOP .

Installation for Ovens Equipped with Casters

It is recommended that in the use of casters a strain relief be 

installed on the appliance . This will prevent any excess strain 

on the terminal connection if the appliance is rolled out for 

cleaning or servicing .

The front casters of the unit are equipped with brakes to 

limit the movement of the oven without depending on the 

connector and any quick disconnect device or its associated 

wiring to limit the appliance movement .

Please be aware, there is a restraint on the unit and if 

disconnection of the restraint is necessary, be sure to 

reconnect the restraint after the oven has been returned to 

its originally installed position .

Stacking Instructions

To Stack APA on top of an AP1 Unit

WARNING  The maximum number of units to be stacked is 

two additional units on top of the single base unit .

WARNING  DISCONNECT ALL WIRING AND PLUGS FROM 

ELECTRICAL SOURCE .

Items required to complete stacking procedure:

1 – AP1 oven with top and legs .

1 or 2 APA ovens without top and legs .

Phillips screwdriver

7/16” open end wrench .

Summary of Contents for Air Pac AP1













Reviews: