GB
- 19 -
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
The scari
fi
er is delivered unassembled. The grass
basket and the complete push bar must be as-
sembled and mounted before using the scari
fi
er.
Follow the operating instructions step-by-step
and use the pictures provided as a visual guide to
easily assemble the machine.
Fitting the rear wheels (see Fig. 3 and Fig. 4)
•
Insert the axles of the rear wheels into the
openings provided (Fig. 3 / Item A).
•
Secure the wheels with the screws provided .
(Fig. 4/ Item 19)
Fitting the push bar brackets (see Figs. 5
and 6)
•
Remove the star nuts (Fig. 5/Item 13).
•
Connect the push bar bracket (Fig. 5/Item 7)
to the fastening screw. Make sure that the
curve in the tube (Fig. 6/Item A) is on the out-
side.
•
Secure the push bar bracket with the star
nuts.
The same tilt angle must be set for both push bar
brackets!
Fitting the lower push bar (see Fig. 7)
•
Slide the lower push bar (Fig. 7/Item 6) onto
the push bar brackets. Do not forget to slip
the stress-relief clip (Fig. 7/Item 4) onto the
tube first.
•
Join the tubes together using the screws (Fig.
7/Item 17) and star nuts (Fig. 7/Item 13) sup-
plied.
Fitting the upper push bar (see Fig. 8 to
Fig. 10)
•
Position the upper push bar (Fig. 8/Item 5)
such that its holes line up with the holes of the
lower bar.
•
Join the tubes together using the screws (Fig.
8/Item 17) and star nuts (Fig. 8/Item 13) sup-
plied.
•
Use the cable clips (Fig. 9/Item 12) to attach
the power cable to the tubes of the push bars
so that it is possible to open and shut the
ejector flap (Fig. 10/Item 12).
Please ensure that the ejector
fl
ap can be opened
and closed easily!
Assembling the grass basket
(see Figs. 11 and -14)
•
Push both frame parts into each other (Fig.
11).
•
Pull the grass basket over the metal frame
(Fig. 12).
•
Pull the rubber clips over the metal frame
(Fig. 13).
•
To hang the grass basket on the scarifier you
must lift the ejector flap (Fig. 14/Item 10) with
one hand and with the other hand take hold of
the grass bag by the handle and hook it onto
the scarifier from above (Fig. 14).
Danger!
Before you ever hook the grass basket to the sca-
ri
fi
er you must ensure that the motor is switched
o
ff
and the cutting unit is not rotating.
Adjusting the handlebar height (see Fig. 15)
Undo the star nuts (Fig. 15/Item 13) on both sides
of the scari
fi
er.
The height of the handlebar can be set to position
1 or 2 (Fig. 15) during operation.
You must then tighten the quick-release fasteners
again.
The same tilt angle must be set on both sides.
Adjusting the scari
fi
er depth (see Fig. 16)
The scari
fi
er depth is set with the adjustment me-
chanism. Pull the lever in the direction indicated
by the arrow (see Fig. 16) and adjust to the requi-
red position (0/ 1/ 2/ 3). Make sure that the lever
latches in place correctly!
0 =
drive/transport position
I =
scari
fi
er depth 3 mm
II =
scari
fi
er depth 6 mm
III =
scari
fi
er depth 9 mm
Electrical connection
The equipment can be connected to any normal
socket with 230V AC. It is only acceptable to con-
nect it to a shockproof socket with a 16A circuit
breaker. Furthermore, a residual-current-operated
protective device with max. 30 mA should be con-
nected upstream.
Anl_GLVE_1400_34_SPK7.indb 19
Anl_GLVE_1400_34_SPK7.indb 19
07.08.14 15:29
07.08.14 15:29
