background image

Operation 

24 

115051 

Operation 

6.1 

LVS without vacuum controller 

Switch the device (LVS 600 T, LVS 601 T, LVS 602 T) on using the main switch. Vacuum is 

generated immediately and without regulation. Over the regulating valves on the LVS 602 T 

it is possible two customers concomitant to connect. 

6.2 

LVS with vacuum controller 

The LVS is switched on by the rocker switch

 POWER

 located on the device. 

The device is ready for operation after a short initializing routine, during which a signal tone 

sounds and all light elements light up briefly. 

In the version 

LVS with external controller

 

(Order no. 115254-04)

 is the on / off power 

switch on the controller. 

6.3 

Operating modes of the Controller 

The following modes are available: 

0  - 

STOP 

Controller is inactive and can be configured 

1  - 

Manual operation 

With specification of the setpoint and, if required, lowering 

2  - 

Automatic operation   The setpoint is detected automatically from the pressure development 

3  - 

Ultimate pressure 

Pumping out at maximum motor output 

4  - 

Self cleaning 

Motor runs for 2 minutes at open ventilation valve 

6.3.1 

Mode 1, Manual operation 

The vacuum valve is closed when the pressure reaches the setpoint. Closed-loop control be-

tween the set hysteresis and the setpoint has been started. 

For 

operation with a frequency converter

, an analog voltage is output, which controls the 

speed according to the standard tolerance. If the set pressure is not reached, the speed is 

automatically adjusted to the pressure loss. 

If the pressure is actively lowered, after the setpoint has been reached for the first time, it is 

lowered still further within a settable timeframe. The number of ramps can be set up to a 

maximum of 3. Each ramp starts with a holding time. The setpoint then falls in one step to 

the defined starting pressure. The setpoint then falls to the final value over the set time. 

After the last ramp, there is a waiting time until the automatic 

STOP

  

(0 – the last set pressure is held indefinitely until 

STOP

 is pressed manually). 

CAUTION ! 

When setting the ramps make sure that the set value is greater than or equal to the 
starting value of the first ramp. 

The closed-loop control and hysteresis are always related to the current (reduced) setpoint. 

The changed setpoint always applies until the 

STOP

 button is pressed, then the configura-

tion value applies once more. When the pressure reduction has finished, the control is 

stopped, and the system waits until the 

STOP

 button is pressed.  

6.3.2 

Mode 2, Automatic operation 

After selection of the operating mode, the controller starts the evacuation. The pressure drop 

per minute is determined during this process. If increases during distillation by incipient boil-

ing of the pressure, then this pressure value is taken as the setpoint and proceeds in the 

normal control operation. 

Summary of Contents for WELCH LVS 600 T





































































Reviews: