background image

22

Chronic Health 

Effects Summary:

    

Contains a petroleum-based mineral oil.  Prolonged or repeated skin contact can cause 

 

 

mild irritation and inflammation characterized by drying, cracking, (dermatitis) or oil 

 

 

acne. Inhalation of petroleum-based mineral oils can cause respiratory irritation or other 

 

 

pulmonary effects after repeated or prolonged inhalation of oil mists at concentrations 

 

 

above applicable workplace exposure levels.

Conditions Aggravated

by Exposure:     

Personnel with pre-existing disorders should avoid repeated or prolonged  contact with this product.

Target Organs:

   

Skin

Carcinogenic Potential:

  This product does not contain any components at concentrations above 0.1% which are

  

considered carcinogenic by OSHA, IARC, or NTP.

SECTION 4 - FIRST AID MEASURES

Take proper precautions to ensure your own health and safety before attempting rescue or providing first aid.  For more specific 

information, refer to Exposure Controls and Personal Protection in Section 8 of this MSDS.

Inhalation: 

 

Vaporization is not expected at ambient temperatures.  This material is not expected toques

  

 

inhalation-related disorders underanticipated conditions of use.  In case of overexposure, 

 

 

move the person to fresh air.

Eye Contact:

 

 

Check for and remove contact lenses.  Flush eyes with cool, clean, low-pressure water while 

 

 

occasionally lifting and lowering eyelids.  Seek medical attention if excessive tearing, 

 

 

redness, or pain persists.

Skin Contact:

   

Remove contaminated shoes and clothing.  Wipe off excess material.  Wash exposed skin 

 

 

with soap and water.  Seek medical attention if tissue appears damaged or if irritation 

 

 

persists.

 

 

Thoroughly clean contaminated clothing before reuse.  Discard contaminated leather goods. 

 

 

If material is injected under the skin, into muscle, or into the blood stream, seek medical 

 

 

attention immediately.

Ingestion:

 

 

Do not induce vomiting unless directed to by a physician.  Do not give anything to drink 

 

unless directed to by a physician.  Never give anything by mouth to a person who is not fully conscious.  If 

large amounts are swallowed or irritation or discomfort occurs, seek medical attention immediately.

Notes to Physician:

 

The viscosity range of the product(s) represented by this MSDS is 100 to 400 SUS at100°F. 

 

Accordingly, upon ingestion there is a low to moderate risk of aspiration.  Careful gastric 

 

lavage may be considered to evacuate large quantities of material.  Subcutaneous or 

 

intramuscular injections requires prompt surgical debridement.

THE INFORMATION HEREIN IS GIVEN IN GOOD FAITH, BUT NO WARRANTY, EXPRESS OR IMPLIED, IS MADE.

Revision Date: 03/31/09                                                               Revision A   

 

Pg. 2 of 7

Summary of Contents for WELCH DUOSEAL 1397B-01





























Reviews: