background image

13–11–602    Page 17

GROUNDING – Equipment must be grounded in ac-
cordance with Table 250–95 of the National Electrical
Code.

Failure to properly ground the com-
pressor package could result in con-
troller malfunction.

MOTOR LUBRICATION – Long time satisfactory op-
eration of an electric motor depends in large measure
on proper lubrication of the bearings.  The following
charts show recommended grease qualities and re-
greasing intervals for ball bearing motors.  For addition-
al information refer to the motor manufacturer’s
instructions.  The following procedure should be used
in regreasing:

1.

Stop the unit.

2.

Disconnect, tag and lockout the unit from the pow-
er supply.

3.

Remove the relief plug and free hole of hardened
grease.

4.

Wipe lubrication fitting clean and add grease with
a hand–operated grease gun.

5.

Leave the relief plug temporarily off.  Reconnect
the unit and run for about 20 minutes to expell the
excess grease.

6.

Stop the unit.  Replace the relief plug.

7.

Restart the unit.

Rotating machinery can cause injury
or death.  Open main disconnect, tag
and lockout power supply to the start-
er before working on the electric mo-
tor.

MANUFACTURER

TRADE NAME

CHEVRON

SRI #2

SHELL

DOLIUM R

EXXON

UNIREX #2

EXXON

POLYREX

ELECTRIC MOTOR GREASE RECOMMENDATIONS (–30

_

 to 50

_

 C)

Relubrication

Type of Service

       Typical Examples

       Rating

Interval

Up to 150 HP (112 KW)

18 Months

Standard

One– or Two–Shift Operation

Above 150 HP (112 KW)

12 Months

Up to 150 HP (112 KW)

 9 Months

Severe

Continuous Operation

Above 150 HP (112 KW)

 6 Months

Up to 150 HP (112 KW)

 4 Months

Very Severe

Dirty Locations, High
Ambient Temperature

Above 150 HP (112 KW)

 2 Months

ELECTRIC MOTOR REGREASING INTERVAL

Summary of Contents for TWISTAIR EWDQ D





































































Reviews: