background image

 

 

 

 

 

 

 

 

 

 

EC - declaration of conformity 2006/42/EC 

 

 

 

 

 

Hereby the manufacturer 

confirms: 

Gardner Denver Schopfheim GmbH 
Postfach 1260 
D-79642 Schopfheim 

 

 

 

 

 

that the machine:

  

of the: 

vacuum pump 

 

Series: 

C-VLR 

Type: 

C-VLR 60, C-VLR 100, C-VLR 120,  
C-VLR 150, C-VLR 250, C-VLR 251, 
C-VLR 300, C-VLR 400, C-VLR 500, 
C-VLR 301, C-VLR 401, C-VLR 501, 
C-VLR 1000 

 

 

 

 

 

is conform to the regulations of the guideline indicated above. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The following harmonized and national standards and specifications are applied: 

Harmonized standards:: 

 

 

 

 

 

 

 

 

 

EN 1012-2:1996+A1:2009 
 

Compressors and vacuum pumps 

— Safety requirements — Part 2: 

Vacuum pumps 

 

 

 
 

 

 

 

 
 

 

 

 

 
 

 

 

 

These declarations of conformity are invalid when the machine has been modified without prior ap-
proval by us and the approval has been documented in writing. 

 

 

 

 

 

Name and address of the EC person in 
charge for documentation 

Gardner Denver Schopfheim GmbH 
Postfach 1260 
D-79642 Schopfheim 

 

 

 

 

 

Gardner Denver Schopfheim GmbH 

Schopfheim, 1.3.2015  

 

 

 

 

 

 

 

 

 

 

 

Dr. Friedrich Justen, Director Engineering 

 

 

 

 

 

 

 

 

 

C_0080_EN 

 

 

Summary of Contents for Elmo Rietschle C-VLR 60



































Reviews: