background image

D--9--611 Page 10

SECTION 3

LUBRICATION

All DuroFlow blowers are splash oil lubricated at both

the gear and drive ends. Oil is distributed around the

gear housing and drive end chamber by the gears and

specially designed oil flingers.

Series

Vertical Horizontal

Oil Fill Ports

Mounting Mounting

One Port --

45

Shaft & Gear Ends

29 oz.

55 oz.

Interconnected

FIGURE 3--1 -- APPROXIMATE OIL CAPACITIES

RECOMMENDED LUBRICANT

The factory recommended lubricant is AEON PD

Synthetic Lubricant.

AEON PD is formulated

especially for positive displacement blowers to provide

maximum protection at any temperature. One filling of

AEON PD will last a minimum of 4 times longer than a

premium mineral oil, depending on actual operating

conditions. AEON PD contains a special additive

package designed for greater rust and corrosion

protection.

AEON PD Lubricant

Description

Part Number

1 Quart

28G23

Case/12Quarts

28G24

5 Gallon Pail

28G25

55 Gallon Drum

28G28

AEON PD Food Grade Lubricant

Description

Part Number

1 Quart

28H97

Case/12Quarts

28H98

5 Gallon Pail

28H99

55 Gallon Drum

28H100

FIGURE 3--2 -- AEON PD SYNTHETIC LUBRICANT

Machines are shipped without oil in

the sumps. Do not operate before

adding lubricant.

LUBRICATION INSTRUCTIONS

For 45 series models, the oil fill port is located on the

top of the blower at the driveshaft end (see

FIGURE 1-- 2, page 5).

The two oil sumps are

connected by a passageway through the housing

Add oil until the level stabilizes at the center of the sight-

glass(es).

Oil level at the sight glass must be

established when the blower is not operating.

Add fresh oil as required to maintain proper level.

Do not overfill as this will tend to

cause excessive heating of the gears,

oil to leak through the vent holes, and

may damage the unit.

AEON PD Synthetic Lubricant should be drained after

6000 hours of operation. Re--fill with fresh AEON PD

oil. If mineral oil is used, perform the above oil--change

maintenance every 1500 hours. Recommended

service intervals are for normal blower operating condi-

tions. Severe operating conditions may warrant more

frequent oil changes. Laboratory analysis of lubricant

should be used to help determine the optimum oil

change interval.

For best performance and equipment protection, use

AEON PD Synthetic Lubricant, which has been specifi-

cally formulated for positive displacement blowers. If

you choose not to use AEON PD Synthetic Blower

Lubricant, select an oil with rust and oxidation inhibi-

tors, anti--foam additives, and the viscosities listed in

FIGURE 3--3, page 12.

Do not use an oil that

contains EP additives.

Summary of Contents for DuroFlow 45 Series




































Reviews: