Gardena 15001-26 Operator'S Manual Download Page 49

Page: 49 / 56

8 Technical data

8.1 Technical data

Data

SILENO city

smart SILENO city

SILENO life

smart SILENO life

Dimensions

Length, cm / in.

55 / 21.7

58 / 22.8

Width, cm / in.

38 / 15.0

39 / 15.4

Height, cm / in.

23 / 9.1

Weight, kg / lb

7.3 / 16

8.3 / 18

Electrical system

SILENO city

smart SILENO city

SILENO life

smart SILENO life

Battery, Lithium-Ion 18 V/2.0 Ah Art.No

590 21 42-02, 590 21 42-04, 584 85 28-03, 584 85 28-05

Battery, Lithium-Ion 18.25 V/2.0 Ah Art.No

590 21 42-03, 584 85 28-04

Power supply (28V DC), V AC

100-240

Low voltage cable length, m / ft.

5 / 16.4

Mean energy consumption at maximum use

4 kWh/month in a 500 m

work area

7 kWh/month in a 1250 m

work area

Charge current, A DC

1 / 1.3

1.3

Type of Power Supply Unit

ADP-40BR XX, ADP 28EW XX,

FW7313/28/D/XX/Y/1.3/PI, FW7313/28/D/XX/Y/1.3, ADP

28AR XX, FW7313/28/D/XX/Y/1.0/PI,

FW7313/28/D/XX/Y/1.0

Average mowing time, min

Average charging time, min

75 / 60

Boundary wire antenna

SILENO city

smart SILENO city

SILENO life

smart SILENO life

Operating Frequency Band, Hz

100-80000

Maximum magnetic field

, dBuA/m

Maximum Radio-frequency power

, mW @60m

<25

XX, YY can be any alphanumeric characters or blank for marketing purpose only, no technical differences.

Measured according to EN 303 447.

Maximum active output power to antennas in the frequency band in which the radio equipment operates.

1298 - 007 - 16.09.2020

Technical data - 49

Summary of Contents for 15001-26

























































Search results

Summary of Contents for 15001-26

Reviews:

Related manuals for 15001-26

Brands by name

Popular brands

Gardena 15001-26, Operator'S Manual

Search results

Summary of Contents for 15001-26

Reviews:

Related manuals for 15001-26

Brands by name

Popular brands