GARDASOFT TR-HT2 Series User Manual Download Page 7 | Manualshive

Page: 7 / 78

background image

TR-HT2xx LED Controller - User Manual

1

Getting started

Before you use this product, make sure that you have read and
understood

Section 2, Safety

, (or

Section 3, Sicherheit

, or

) and , and that you have checked the TR-HT2xx fulfils your

requirements. Throughout this manual, all versions of the controller will be
referred to as the TR-HT, unless specified otherwise.

Mount

the TR-HT (see

Section 5, Mounting the TR-HT

) and

connect

it up

as required (see

Section 6, Connecting the TR-HT

).

Set up

the TR-HT for the desired operation as described in

Webpage configuration

or

Section 12, Configuration commands

.

We recommend that you visit

www.gardasoft.com

for application notes on

this product. There is also a support web page there, which has
information on trouble-shooting problems.

1.1

TR-HT features - a summary

The TR-HT product is a dual channel LED lighting controller for use in
machine vision applications that can deliver 50A per channel in pulse
mode. The TR-HT has Ethernet connectivity and may be controlled
through a web portal and, using

triniti

™ technology, allows the control of

your illumination system (if it is

triniti

enabled).

The TR-HT automatically senses and sets up

triniti

-enabled lights on

connection. It has SafeSense™ which allows the controller to
automatically sense the characteristics of your lights. The TR-HT also has
SafePower™ which ensures low heat dissipation and the ability to deliver
higher currents with a reduced need for additional heat sinking.

1.2

GigE Vision

TM

The TR-HT is GigE Vision™ compatible. This means that any
compatible GigE Vision client image processing software
allows the user to view and change controller settings. GigE
Vision is an industry standard protocol running on Ethernet which provides
easy configuration and control of cameras and other devices.

—

7

—

«
...
5
6
7
8
9
...
»

Summary of Contents for TR-HT2 Series















































































Reviews:

No comments

Related manuals for TR-HT2 Series

ControlMaster CM15

Brand: ABB Pages: 28

DELTAFLUX MT100

Brand: PIETRO FIORENTINI Pages: 16

Brand: Waters Pages: 55

Brand: Paradox Pages: 2

Brand: Unitech Pages: 11

Brand: B meters Pages: 10

Brand: Wavelink Pages: 69

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: Febco Pages: 12

Brand: HANYOUNG NUX Pages: 74

Brand: HANYOUNG NUX Pages: 36

Brand: HANYOUNG NUX Pages: 2

Brand: HANYOUNG NUX Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands