GARDASOFT TR-HT2 Series User Manual Download Page 60

Page: 60 / 78

TR-HT2xx LED Controller - User Manual

12.3.3 General commands

Any changes you make using Ethernet commands are not saved
permanently until you send the

command.

Report the TR-HT firmware version

This command returns the firmware version running on the TR-HT.
For example, typing:

returns

TR-HT220-50 (HW01) V037pre04

Set the rating of a light

This command sets the current or voltage rating of the light:

VLo,v,c

Where:

output channel (1 to 2)

voltage rating (12 to 24)

current rating (10mA to 5A).

Note:

If the light is current rated, set the voltage rating to 0; if it is

voltage rated, set the current rating to 0.

Set continuous mode

This command sets the output to continuous mode and allows the
brightness to be set:

RSc,s

Where:

output channel (1 to 2)

brightness as a percentage (0 to 100).

Set pulse mode

This command sets the output to pulse on a trigger input:

RTc,p,d,s

RTc,p,d,s,r

Where:

output channel (1 to 2)

pulse width in milliseconds (0.02 to 999)

delay from the trigger pulse in milliseconds
(0.02 to 999)

—

Summary of Contents for TR-HT2 Series















































































Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands

GARDASOFT TR-HT2 Series, User Manual

Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands