GarageAce ET30 Instruction Manual Download Page 4

4

1. SAFETY WARNINGS

Warning — It is vital for the safety of persons to follow all instructions. Failure to comply with the following
safety rules may result in serious personal injury and/or property damage.

Do not operate the garage door operator unless the garage door is in full view and free from objects such as
cars and children/people. Make sure that the door has finished moving before entering or leaving the garage.

Do not operate the garage door operator when children/persons are near the door. Children must be
supervised near the garage door at all times when the door opener is in use. Serious personal injury and/or
property damage can result from failure to follow this warning.

Do not allow children to operate the garage door operator. Serious personal injury and/or property damage
can result from failure to follow this warning.

Regularly check to make sure that the safety obstruction force is working correctly, and is tested (by placing a
50mm high object on the floor) and set as per the installation instructions manual. Failure to follow the manual
could result in serious personal injury and/or property damage. This test must be repeated at regular intervals
and the necessary adjustments made as required.

Do not disengage the door opener to manual operation with children/persons or any other objects including
motor vehicles within the doorway.

Wall switch or transmitter must be installed high enough and make sure children can’t reach them.
The door opener is not intended for use by young children or infirm persons without adequate supervision.
Children should be supervised to ensure that they do not play with the remote transmitters or the operator.

Keep hands and loose clothing clear of the door and door opener at all times. If the roll up door is the only
entrance to the garage, a back up battery must be installed and checked weekly.

The unit should be installed so that it is protected from the elements. It should not be exposed to water or rain.
It is not to be immersed in water or sprayed directly by a hose or other water carrying device.

The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage
door installer prior to installation of the operator.

Frequently examine the installation, in particular cables, springs and mountings for signs of wear, damage or
imbalance. Do not use the door if repair or adjustment is needed since a fault in the installation or an
incorrectly balanced door may cause injury. Do not attempt to repair the door yourself as hardware is under
extreme tension.

Remove or disengage all garage door locks and mechanisms prior to installation the operator.

Summary of Contents for ET30



















Reviews: