background image

14 

 

 

Placing the stickers ensures that you can quickly find the balance point every time 
simply by lining up the stickers. 

NOTICE 

 

If you plan to use only one or two of the bikes at a time, you can use the 
remaining stickers to indicate the balancing points for each scenario. 

 

If one bike is used more often than the others, you may want to place it 
in the center. This may allow the lifter to stay balanced when the center 
bike is removed without needing to reposition the frame. 

 

Bikes of varying sizes should be positioned the same each time or the 
sticker placement will not indicate the correct balance points. 

 

11.

 

Use the 

Device Control

 screen on the MyLifter app to lift the bikes until the wheels 

are barely touching the floor. 

12.

 

In the MyLifter app, tap the 

Set Low

 button to set the smart low point. 

13.

 

Tap the 

Manual Lift Up

 button to lift the bikes to the ceiling, making sure to leave 

six inches of ceiling clearance. 
 

CAUTION 

When you use the Manual Lift Up button, make sure you do not run the pulley frame 
into the MyLifter. Running the pulley frame into the lifter could cause damage to the 
lifter, damage personal property, or cause personal injury. 

 

14.

 

Tap the 

Set High

 button to set your smart high point. 

Now you can easily lift or lower your bikes with the simple tap of a button. 

 

 

Summary of Contents for Multi-Bike Lifter

















Reviews: