ADJUSTMENT
INSTALLATION
1. Direction and Lens
The camera body is set in a tri-axial mounting allowing movement in the
pan, tilt and rotational planes.
1) Adjust the direction of the lens so it faces the subject
2) Move the lever to adjust focus and angle of view
3) When you finished adjusting the direction of the lens, tighten the locking
screw with a screwdriver.
1)
3)
2)
Surface mount
Flush mount
(embedding in ceiling or wall)
(Attaching to a gang box)
* Use the elastic band to
hang the camera unit
upon necessity for the
installation.
WARNING
: Do not
release your hands
from the camera
unit until securing it.
* Mounting
Adaptor Ring
(optional)
* Camera Unit
Please use fixing screws suitable for the material of the ceiling or wall when
attaching the camera body. The mounting screws provided are not recommended
to use at a conditionns.
☞
Attention
*
Surface mount
This section explains how to install the unit where cables are running through the
interior of the ceiling or wall.
1. Drilling holes in the ceiling or wall: Use the template included to mark out the
position on the ceiling or wall where you want to install the unit.
2. When running cables through the interior of the ceiling or wall : Use the template,
and drill two or three holes for screws used to attach the camera body and one hole
for the cables (Cables).
*
Flush mount
- Embedding in the ceiling or wall
Be sure to use the Mouting Adaptor Ring when embedding the unit in the ceiling or wall
1. Drilling holes in the ceiling or wall : Use the template included to mark out
the position on the ceiling or wall where you want to install the unit.* Use the template,
drill 4 holes for screw used to attache the Mounting Adaptor Ring. Then, follow the
perforations on the template and cut out a hole to embed the camera body.
2. Attaching the Mounting Adaptor ring : Attach the adaptor ring to the ceiling or wall to
which you want to attach the camera body. Please use fixing screws suitable for the
material of the ceiling or wall when attaching the camera body. We recommend using
screws with a 4mm diameter.
3. Attaching the camera body : Remove the surface mount cover from the camera
body. Remove the body cover and attached camera body to the Mounting Adapter Ring.
- Attaching to gangbox
1. Remove the surface mount cover from the camera body.
2. Attaching the camera body : Attach the camera body to the gangbox.
Please use screws that are suitable for the gang box.
(Use breakable holes on the camera body bottom)
The picture image may deteriorate when
the lens is leaned toward ceiling or wall
to view through the circled vertical area
and the effect may depending on the
view angles.
☞
Attention
CBC Co.,Ltd
Tokyo, Japan
www.GANZ.jp
Direction and Enter Guide
Up
Down
Enter
Right
Left
1) LENS
2) SHUTTER/AGC
3) WHITE BALANCE
4) BACKLIGHT 5) PICTURE ADJUST 6) ATR(D-WDR)
7) MOTION DETECTION
BRIGHTNESS adjusts DC level of the lens
* Simply make the adjustment in the following order to help
make the focusing easier:
- Select MANUAL
- Adjust lens focus well
- Then return to AUTO
Turn the Switch toward Left or Right side, Select AUTO or MANUAL
Right
Left
SETUP
SETUP MENU
HIGH LUMINANCE
LOW LUMINANCE
MODE
AUTO IRIS
MODE
SHUT+AGC
ATW
PUSH
USER1
USER2
ANTI CR(ANTI COLOR ROLLING)
MANUAL
PUSH LOCK
Attention
Attention
Attention
BRIGHTNESS 000 ~ 255
BRIGHTNESS x0.25 ~ x1.00
SHUTTER 1/60 ~ 1/10000 *Flickerless
NTSC :1/100
PAL : 1/120
AGC 6.00 ~ 44.80
SPEED 000~ 255
DELAY CNT 000~ 255
B-GAIN 000 ~ 255
R-GAIN 000 ~ 255
B-GAIN 000 ~ 255
R-GAIN 000 ~ 255
LEVEL 019 ~ 078
Attention
When MOTION DEC ON,
only 4 AREAS available.
* NR : DIGITAL NOISE REDUCTION
* Y LEVEL : B/W SIGNAL LEVEL
* C LEVEL ; COLOR SIGNAL LEVEL
* Return to Factory Setting
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PIC ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
SETUP
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PIC ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
SETUP
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PIC ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
SETUP
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PIC ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
SETUP
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PIC ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
Do not change
the above factory-set levels
WARNING
AUTO
MANUAL
ON
ON
Japanese
SHUT + AUTO IRIS
MODE
AGC
OFF
BLOCK DISP
ON
MOTION DET
TOP 000 ~ 244
BOTTOM 000 ~ 244
LEFT 000 ~ 474
RIGHT 000 ~ 474
DETECT SENSE 000 ~ 127
OFF
ENABLE
MONITOR AREA
ON
OFF
AREA SEL
1/4 ~ 4/4
INDOOR
AGC x0.50~ x2.00
ENVIRONMENT OUTDOOR
MIRRO OFF - ON
LUMINANCE MID-HIGH-LOW
CONTRAST MID-HIGH-LOW
BRIGHTNESS 000 ~ 255
CONTRAST 000 ~ 255
SHARPNESS 000 ~ 255
HUE 000 ~ 255
GAIN 000 ~ 255
BLC-HLC
ON
AUTO
B/W
COLOR
8) PRIVACY MASKING
2nd Page OSD
SETUP
SETUP MENU
PRIVACY OFF
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
ON
ON
PRIVACY
TOP 000 ~ 244
BOTTOM 000 ~ 244
LEFT 000 ~ 474
RIGHT 000 ~ 474
OFF
AREA SEL
1/8 ~ 8/8
COLOR
1 ~ 8
TRNSP
1.00 ~ 0.00
MOSAIC
Y LEVEL 000 ~ 15
C LEVEL 000 ~ 15
Y/C
OFF
Y
C
NR MODE
9) DAY/NIGHT
SETUP
SETUP MENU
PRIVACY OFF
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
10)NR 11)CAMERA ID 12)SYNC 13)LANGUAGE 14)RESET
SETUP
SETUP MENU
PRIVACY OFF
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
TYPE
DC
AUTO IRIS
SPEED 000 ~ 255
AUTO
MANUAL
MODE
AUTO
OPEN
CLOSE
German French Russian Portuguese Spanish Chinese
DAY/NIGHT
DELAY CNT 000 ~ 255
DAY->NIGHT 000 ~ 255
NIGHT->DAY 000 ~ 255
ON
OFF
BURST
3. OSD Menu
* START SET UP MENU
Press the Middle Multi Tact Switch, the main setup menu is displayed on the monitor
screen
Select the function
by using the switch
* A function with the icon
has sub menus.
To select a sub menu,
select a function with
the icon and press
the switch
Up
Down
Enter
SETUP MENU
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PIC ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
1st Page OSD
OSD MENU FUNCTION
LENS
SHUTTER/AGC
WHITE BAL
BACKLIGHT
PICT ADJUST
ATR
MOTION
EXIT
AUTO MANUAL
AUTO MANUAL
ATW PUSH USER1 USER2 ANTI CR MANUAL PUSH LOCK
OFF BLC HLC
MIRRO BRIGHTNESS CONTRAST SHARPNESS HUE GAIN
OFF ON
OFF ON
PRIVACY
DAY/NIGHT
OFF ON
AUTO COLOR B/W
NR
CAMERA ID
SYNC
LANGUAGE
CAMERA RESET
2. Switches
2) Multitack Switch for OSD
1) Slide Switch for Sync. System
Use the Multi Tact Switch within the camerra
Use the Slide Switch within the camerra
* L-L : Line Lock
* INT : Internal
INT
L-L
* OSD automatically reflects Power and Sync Switch positon to be set as:
Power
DC 12V
INT
INT
* INT: Internal Sync
* LL : Line Lock
LL
INT
INT
INT
LL
LL
AC 24V
Sync Switch
Sync
"Flickerless" function can be available by SHUTTER/AGC MANUAL
SHUTTER 1/100(NTSC) 1/120(PAL) return to "AUTO" to fix the setting
For regular Auto-Iris use, ensure to set "AUTO IRIS" (Not "SHUT+AUTO IRIS)
in this “SHUTTER/AGC" OSD menu
