4
www.gantner.com
Electrical connections
TCP/IP with external power supply
GAT Info 6100
3
1
2
R
X +
TX
-
TX
+
GND
N
O 1
C 1
IN1 -
IN1 +
R
X -
VI
N +
TCP/IP
Power supply unit
e.g. GAT Power Supply SP014/1
V
Out+
GND
A
B
Mains power
Safety instructions
- This device must be installed by qualified personnel only.
- The applicable safety and accident prevention regulations
must be observed.
- Safety devices must not be removed.
- Please observe the technical data of the device specified
on the data sheet.
- The device must be disconnected from the power supply
prior to installation, assembling or dismantling.
Valid as from February 15
th
2016 • Technical data subject to modifications without notice!
DB_GAT-INFO6100--EN_11.indd • PartNo.: 860380
Network
Ethernet connection (1) via screw terminals.
Power supply
DC supply (see technical data), e.g. via GANTNER GAT Power Supply
SP014/1 (2). The power input is protected against reverse polarity.
Recommended cables:
Ethernet: min. CAT 5 (STP) for 100 MBit
Wiring standard
Ethernet 10/100 MBit
Connection to the device front part
Plug the connection cable into the socket on the device back part
(consider alignment).
Attention: The socket (3) for the connection cable between the device
back part and the device front part must be clean to ensure
correct operation.
Relay output
No function.
Optocoupler input
No function.
568A
568B
TX +
green/white
orange/white
TX -
green
orange
RX +
orange/white
green/white
RX -
orange
green
Applicable for the following devices:
- GAT Info 6100 F
FCC NOTICE (Class B)
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, included interference that
may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Warning Statement
[Any] changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
GANTNER is committed to meeting or exceeding the requirements of the
RoHS directive (2011/65/EU). The RoHS directive requires that manufacturers
eliminate or minimize the use of lead, mercury, hexavalent chro-mium, cadmium,
polybrominated biphenyls and polybrominated diphenyl ethers in electrical and
electronic equipment sold in the EU after July 1, 2006.
This product is herewith confirmed to comply with the requirements set out
in the Council Directives on the Approximation of the laws of the Member
Statesrelating to Electromagnetic Compatibility Directive 2004/108/EG.
This product is in conformity with the following EC directives, including all
applicable amendments:
- 1999/5/EC (R&TTE directive)
- 2004/40/EC (Limitation of human exposure to electromagnetic fields)
- 2011/65/EU (Restriction of the use of certain hazardous substances in
electrical and electronic equipment)
The WEEE symbol on GANTNER products and their packaging indicates that the
corresponding material must not be disposed of with normal household waste. Instead,
such marked waste equipment must be disposed of by a designated electronic waste
recycling facility. Separating and recycling this waste equipment at the time of disposal
will help to conserve natural resources and ensure that it is recycled in a manner that
protects human health and the environment. For more information on recycling an item
marked with the WEEE symbol, please contact your local city office or your household
waste disposal operation.
RoHS
COMPLIANT
