manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 194

A:192

AK 98 Dialysis Machine - Technical data and specifications

HCEN12745 Revision 10.2016

Program version 2.xx

Valid under conditions that preventive maintenance and repair have been performed at
least every other year by an authorized technician.

14.6.5

Energy and water consumption

Typical energy consumption and energy delivery to environment and drain at inlet
water temperature of approximately 23 °C given the conditions stated in Table 14-27

“Consumption conditions”

on page A:192.

Energy consumption

2.2 kWh

Energy delivery to the environment

1.3 kWh

Energy delivery to the drain

0.9 kWh

Table 14-25. Energy consumption

Water

140 L

A concentrate

2.9 L

B concentrate, liquid

5.0 L

B concentrate, dry powder

0.4 kg

Table 14-26. Consumption of water and dialysis fluid concentrates

Data in Table 14-25

“Energy consumption”

on page A:192 and Table 14-26

“Consumption of water and dialysis fluid concentrates”

on page A:192 have been

obtained given the conditions stated in this table.

Dialysing time

4h plus preparation time and post treatment
operation

Dialysis fluid flow

500 mL/min

Blood flow

300 mL/min

Ultrafiltration flow

0,5 L/h

Dialysis fluid temperature

37 °C

Type of disinfection

Heat disinfection with CLEANCART C
cartridge

Table 14-27. Consumption conditions

14.7

Standards

The machine complies with the following standards:

IEC 60601-1:2005/AMD1:2012/COR1:2014 Medical electrical equipment - Part 1:
General requirements for basic safety and essential performance.

IEC 60601-1-2:2014 Medical electrical equipment - Part 1-2: General requirements for
basic safety and essential performance - Collateral standard: Electromagnetic
compatibility - Requirements and tests.

IEC 60601-1-6:2010/AMD1:2013 Medical electrical equipment - Part 1-6: General
requirements for basic safety and essential performance - Collateral standard:
Usability (+ Amendment 1).

IEC 60601-1-8:2006 + AM1:2012 Medical electrical equipment -- Part 1-8: General
requirements for basic safety and essential performance - Collateral Standard:
General requirements, tests and guidance for alarm systems in medical electrical
equipment and medical electrical systems.

IEC 60601-1-11:2015 Medical electrical equipment - Part 1-11: General requirements
for basic safety and essential performance - Collateral Standard: Requirements for

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands