Gama Garden GBC 43 Instruction Manual Download Page 27

Acquaer Ltd. 

 

www.gamagarden.eu

 

H-4900, Fehérgyarmat Szatmári út 11.

 

 

 

 

 

TROUBLESHOOTING GUIDE 

 

2.

 

LOW OUTPUT 

symptom 

probable cause 

remedy 

flameout when speedup 

 

the smoke is thin, 

carburetor spout backward 

fuel filter obstruct, 

fall short of fuel 

muffler 

fouled 

with 

oily 

deposits 

clean  fuel  filter

clean  fuel 

road

 

adjust carburetor 

clean the oily deposits 

compress press is shortage 

piston

piston ring

 

cylinder attrite

 

replace piston

piston ring 

engine leak 

Conjoint surface of the 

Cylinder and crank cast leak 

repair 

the end of two crank shaft leak 

the seal is bad 

replace seal 

 

engine overheats 

 

burning room fouled with   

oily deposits 

avoid use it for long time

 

high speed and heavy load 

clean the oily deposits 

 

3. ENGINE RUNNING UNSTABLE

 

symptom 

probable cause 

remedy 

there are metal knock sound   

piston

piston ring

 

cylinder attrite

   

piston pin

piston attrite 

bearing of crank shaft attrite 

replace piston

piston ring 

 

replace piston pin

piston 

replace bearing   

there are metal knock sound 

engine overheats 

 

burning room fouled with   

oily deposits 

gasoline branded is unfit 

avoid use it for long time

 

high  speed  and  heavy  load 

clean the oily deposits 

 

replace require branded octane 

engine ignition break off 

there is water in fuel 

spark gap is wrong 

coil gap is wrong 

instead fuel 

adjust spark gap 0.6-0.7mm 

adjust coil gap 0.3-0.4mm 

 

4. THE ENGINE SUDDENLY STOPPED 

probable cause 

remedy 

fuel is use up 

spark  plug  fouled  with  oily  deposits  and  short 

circuit 

high voltage wire fall off 

add fuel 

clean the oily deposits 

connect 

 

Summary of Contents for GBC 43





























Reviews: