background image

12

1001RB Series

1001RB Series Combos

The 1001RB Series combos deliver the1001RB’s unique
features and distinct sound by using a variety of
internal speaker configurations, GK’s RBH cabinet
technology and a unique Lock N’ Roll transport
system.

Speaker Configurations:

1001RB/115

One 8 Ohm 15

speaker and

one 8 Ohm horn

1001RB/210

Two 16 Ohm 10

speakers

(wired in parallel for an 8
Ohm equivalent load)and
one 8 Ohm horn

The 1001RB combo electronics are identical to the1001RB
head and are rated for the same maximum power output
and speaker load (540W into 4 Ohms, and 50W into 4
Ohms).  Maximum power is achieved by connecting one 8
Ohm extension cabinet (such as the 210RBH,  410RBH,
or 115RBH) in addition to the combo’s internal 8 Ohm
speaker load.  To drive more than one extension cabinet,
the combo’s internal speaker can be disconnected by
unplugging the Speakon cable connected to the combo’s
back panel.  Below is a detailed description of the maxi-
mum loads the combos can drive.

Maximum recommended load with the

internal speaker connected:

One 8 Ohm cabinet on the 540W Amp.
One 8 Ohm horn on the 50W Amp.

Maximum recommended load with the

internal speaker disconnected:

One 4 Ohm, or Two 8 Ohm cabinets on the 540W Amp.
One or Two 8 Ohm horns on the 50W Amp.

Lock N’ Roll Transport System:

The Lock N’ Roll transport system is designed for quick
and easy rolling of the combo on flat surfaces such as
carpet, flooring, pavement, etc.  To engage the Lock N’
Roll handle,  first move the combo into the upright
position (front perpendicular to the ground).  Next,  stand
behind the cabinet and lift the Lock N’ Roll handle up with
your right hand.  The handle will lock into place after
about 1 1/2 feet.  Finally, grab the handle and tilt towards
the back of the combo.  The wheels on the bottom of the
cabinet will automatically engage and allow smooth
rolling.

To disengage the Lock N’ Roll system, first return the
combo to its upright position and stand behind the unit.
Next, with your left hand, pull the locking latch at the
base of the handle to your left, while pushing the handle
down gently with your right hand.  Finally, push the
handle down until it stops and is flush with the top of the
combo.

The 1001RB Series combos are designed for maximum
setup versatility to accommodate a variety of playing
situations.  For practicing and close monitoring situations,
tilt the cabinet back into its “Rock Back” position.   For
stronger bass and audience projection, leave the combo in
the upright position.

1001RB 

Series 

Combos

Summary of Contents for 1001RB

















Reviews: