GALLERY FIREFOX 5 ECO Installation Manual And User Operating Instructions Download Page 16

16 
 

 
2.4.7 De-ashing 

 
During stove use, whilst burning anthracite or a mix of wood and anthracite, from time to 
time the fire must be agitated with a poker to remove ash ensuring  
 
airflow through the fire bed and allowing the fire to burn over the whole grate. Ensure 
you use the glove provided. 
 

2.4.8 Recommended Fuels 

 

Please  note  that  HETAS  Ltd  Appliance  Approval  only  covers  the  use  of  wood  logs  and 
approved smokeless fuels on this appliance.  HETAS Ltd. Approval does not cover the use 
of other fuels either alone or mixed with the recommended fuels listed above, nor does it 
cover instructions for the use of other fuels.

 

 

Only the fuels specified for use in this manual are recommended.  Any unauthorised fuel 
use will void the stove warranty. 
 
Wood - 

Only kiln-dried or well-seasoned wood with a moisture content reading of less 

than 18% is recommended.  A moisture meter is a useful device to measure the moisture 
content of wood.  Generally

, wood seasons at about 1” (25mm) per year, so a log split 

such that along its length no dimension is greater than 3” (75mm), it would take abou

t 3 

years to dry.  A dry log will produce up to four and a half times more heat output than a 
freshly cut log.  Wet logs take heat to dry and if burned in this state will cause incomplete 
combustion  and  will  be  detrimental  to  the  performance  of  the  appliance,  and  the 
environment. 
 

Other Solid Fuel 

 

“Authorised” fuels include anthracite large nuts, briquettes smokeless 

fuel,  ie.  Ancit,  Phurnacite,  Taybrite,  Homefire  Ovals  suitable  for  closed  appliances.  
Bituminous coals can cause tar deposits and burn very hot, it is also recommended that 
the sulphur content is checked when burning this type of fuel. 
 

2.4.9 Unauthorised Fuels 

 
Do not burn Wildfire, Housecoal, household coal, petroleum cokes or household waste.  If 
in doubt consult your supplier or the Solid Fuel Association. 

Please note that when refuelling with solid fuel, do not pile fuel higher than 30 degrees 
from  the  front  bar  rearwards 

  over-fuelling  can  cause  excess  smoke  and  produce 

temperatures beyond the designed rating of the stove causing damage to internal parts 
and chimney system. 

This stove is designed to be operated with the door closed, except for when lighting for 
the first time when initially trying to establish the fire. When refuelling always minimize  

Summary of Contents for FIREFOX 5 ECO

























Reviews: