TEMPERATURE LOCK
The Temperature Lock feature deactivates the temperature control function from the control panel. All other functions on the control panel will
operate normally. Temperature Lock is most often used by those who do not want others to change the set temperature of the spa water.
To activate the Temperature Lock, press “SET” “TEMP
▲
“ button and hold for three seconds until lock symbol is illuminated.
To deactivate the Temperature Lock, press “SET” “TEMP
▲
“ button and hold for three seconds until the lock symbol is no longer illuminated.
ADVANCE MODE CONTROL (SET BUTTON)
The “SET” button is used to initiate advanced panel features such as the spa panel lock, temperature lock, display inversion, and color wheel mode.
MAIN CONTROL PANEL BUTTONS AND DISPLAY
Your spa control system consists of an illuminated Light Emitting Diode (LED) and convenient push buttons that allow you to set the water temperature, as well as the
hydrotherapy jets, mood lighting, and optional jets from the spa control panel.
DISPLAY INVERSION
You may invert the main, four-digit display for easier viewing from inside the spa. Press and hold the “SET” button for three seconds until the display is inverted. Press
and hold the “SET” button for three seconds a second time to invert the four-digit display back to it’s original position.
TEMPERATURE BUTTONS
The set temperature range is from 80°F to 104°F. Higher Temperatures can be reached by using one of the four codes: ut1, ut2,ut3 and ut4. These
settings get progressively warmer, with ut4 the highest at approximately 106°F. (Temperatures of any setting may rise slightly depending on the
current use and condition of your spa, and on outside temperature.
The set temperature of the spa water will automatically be 102°F the first time power is applied. This is the setting programmed at the factory. After
the spa has been set up and used, the last temperature value set by the user will be stored in memory. If power is disconnected from the spa, it will automatically revert
to the last set temperature when power is reapplied.
To display the set temperature of the spa, press the “TEMP
▲
“ or “TEMP
▼
“ button. The set temperature will be displayed, unless the spa is locked (in which case the
word SPA is displayed with the lock symbol). The set temperature display will automatically return to actual temperature after five seconds.To increase the set
temperature of the spa water, press the “TEMP
▲
“ button. Each time the button is pressed, the set temperature display will increment by one degree. If the button is
held down, the set temperature display will increase by one degree every half-second.
To decrease the set temperature of the spa water, press the “TEMP
▼
“ Each time the button is pressed, the set temperature display will decrement by one degree. If
the button is held down, the set temperature display will decrease by one degree every half-second.
If the set temperature value will not change, check the TEMP LOCK and SPA LOCK features. When either of these features is applied, the temperature control is disabled.
JETS BUTTONS
There are two buttons which affect the jet pumps:
The “JETS 1” button activates jet pump 1. When the “JETS 1” button is pressed, the jets symbol will illuminate on the control panel display. The
symbol will remain lit until the button is pressed again to turn off the jet pump 1, or after one hour of continuous operation when the pump is
automatically shut off by the control system.
The “JETS 2” button activates jet pump 2. When the “JETS 2” button is first pressed, the pump is in low speed and the jets symbol illuminates on the control panel
display. Pressing the button a second time switches the jet pump to high speed mode. The symbol will remain lit until the button is pressed a third time turning jet
pump 2 off, or after one hour of continuous operation when the pump is automatically shut off by the control system.
MANUAL CLEAN BUTTON
The “CLEAN” button has been provided as a convenient timer for water maintenance. When the “CLEAN” button is pressed, Jet pump 1 will activate. The jet pump
symbol will flash on and off until the cleaning cycle is complete. The total cleaning cycle time is ten minutes. If the clean cycle does not engage, make sure the SPA
LOCK is deactivated. SPA LOCK disables the controls on both the main, and auxiliary control panels.
AUTOMATIC CLEAN CYCLE
The automatic clean-up cycle operates in the following manner:
• The air blower activates for one minute for Geneva
TM
, Niagara
®
and Tahitian
®
spas
• Jet pump 2 runs for one minute
• Jet pump 1 runs for eight minutes (except for the Elation
®
and Aspire
TM
spas which runs for nine minutes).
This system is initiated five minutes after the spa is powered up, then once every 24 hours.
Press the “SET” + “CLEAN” button simultaneously to reset the 24 hour cycle time.
AIR JETS BUTTONS
(Available on Geneva, Niagara and Tahitian spas)
The “AIR” button activates the air blower. When the “AIR” button is pressed, the air symbol will illuminate on the control panel display. The symbol
will remain lit until the button is pressed to turn off the air blower, or after fifteen minutes when the blower is automatically shut off by the control
system. While the air blower is on, air-only jets are operating throughout the spa. To stop the air blower when active, simply press the “AIR” button.
21
OPERATING INSTRUCTIONS
