2
Insert the stem with the handlebars into the head tube of the scooter frame. Observe the minimum
insertion depth. Align the stem with the handlebars so that the longitudinal axis of the handlebars is
perpendicular to the axis of travel. Then tighten the handlebars with the Allen bolt in the stem (see.
Picture 4). For the correct geometry, a slight bend of the front fork must point forward.
If a brake is included, insert the oval end of the brake cable into a larger round hole (different types of
levers may have different attachments) located on the brake lever and insert the brake cable into the
socket on the bottom of the handlebars (see. Picture 3).
Press both V-brake arms towards the wheel rim and use the appropriate wrench to adjust the brake
blocks so that when breaking the blocks rub their entire braking surface against the side of the rim
(see. Picture 7) if necessary, tighten or loosen the brake cable with the clamping screw (see. Picture
5) or adjusting screw on the brake lever so that there is a gap of approx. 1-2 mm between the rim and
the brake block (see. Picture 6). If the wheel does not turn freely and "brakes" on one side, this can be
adjusted by tightening the tensioning screw on the V-brake arm, which "brakes" the wheel (see.
Picture 5), or by loosening the tensioning screw on the V-brake arm, which is further from the rim so
that the wheel rotates freely. Always check the function of the brake before riding. If the brake lever
(on the handlebars) contains an adjusting screw (located on the side of the lever), it can be shortened
to shorten the distance between the lever and the handle (according to the size of the hand).
If the stand is not attached, screw it to the frame at the bottom so that the stand tilts to the left from the
rider's point of view (see. Picture 1).
Inflate the tires according to the rider's weight, but not more than the value marked on the tires (bar /
psi). If you are unfamiliar with the assembly steps, entrust the product to a professional service or
contact your dealer.
RIDING INSTRUCTIONS
Always keep both hands on the handlebars when riding. While bouncing with one foot, stand on the
footboard of the scooter with the other foot. Rotate the bounce leg regularly. To brake, press the brake
levers on the handlebars. Brake with the rear brake, which is usually controlled by the right lever. Use
the front brake only when braking or in an emergency.
WARNING: Sudden braking can cause a fall.
SAFETY INSTRUCTIONS
Read the manual carefully before assembly and use. Scooter Calypso has a maximum load capacity
of 90 kg. Zenit scooter has a maximum load capacity of 100 kg. Tighten all bolts and nuts before use.
For safe riding always wear a helmet, knee, elbow, and wrist protectors and sturdy shoes. Scooter is
not designed for riding on public roads or traffic and riding in the dark or dusk. Do not use the scooters
in the rain, on wet or slippery surface, gravel, and snow. Check bolts connections, tightening
mechanisms and brakes regularly to prevent accident while riding. Do not brake too hard and
suddenly - you could fall. The manufacturer is not responsible for damage on the product or for any
damage that may occur while using this product. Scooter is intended for 1 rider only - no passengers!
Not suitable for children under 3 years, contains small parts that the child may inhale. Speed reduction
mechanisms (brake blocks, rims, etc.) heat up during use, do not touch them after use!
MAINTENANCE
It is recommended to entrust maintenance to specialized service. Regularly check, tighten, or adjust
following parts: bolts connections, tightening mechanisms, lubricate sliding parts (wheel bearings,
handlebar bearings etc.) check cables and brake parts. Before each use check tightening of all bolts
and function of break. In case you notice wear of some parts (tires, bearings, breaking parts etc.)
replace them with parts with same parameters and adjust them properly. Clean the scooter with
aggressive cleaning agents, for bearings use oil for bikes. After use it is recommended to entrust
tightening of wires evenly by specialized service.
WARNING: Breaking pads and rim must be protected against oil and grease.
