Galanz WMUK001W User Instruction Manual Download Page 8

The door lock is activated once the “Start/Pause” button is pressed. Turn the knob to position “    ”
 and the door lock is deactivated after two minutes.

When the temperature inside the drum is above 60

, the door lock is locked.  

When the water is above a certain level, the door lock is locked.  
When the washing cycle is finished, the door lock is unlocked after two minutes.

How to use the washer

Use process

Washing programme chart

Washing symbol

Fabric

Programme

Cottons, linens or cotton mix fabrics, e.g. table linen, towelling, 
underwear, T-shirts etc.

Cottons, linens or cotton mix fabrics, e.g. table linen, towelling, 
underwear, T-shirts etc.

Machine-washable or hand-washable wool or wool blend fabrics. 
If the care label does not specify a temperature, wash using the 
cold setting. Also suitable for hand-washable silks.
Reduce the spin speed.

Small loads of items which require freshening up and which can 
be washed on a Cotton programme.

Standard

Quick

Separate spin for cotton and linen items

Rinse+Spin

Spin

Cotton

Synthetic

Wool

Synthetic or mixed fabrics, underwear, coloured garments, 
non-shrink shirts

This programme can be used for rinsing items which can be 
washed on a Cotton programme. Do not add any detergent.

 The machine is fitted with a balance control device, which ensures the machine is stable 
during the spin. To protect the machine, it will cut in if the laundry is not evenly distributed 
in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen 
several times before the unbalance disappears and normal spinning can resume. If, after 15 
minutes, the laundry is still not evenly distributed in the drum, the machine will not spin. In 
this case, redistributed the load manually and reselect the spin programme.

Door lock

Use process

Cleaning and Maintenance

Important:
Do not try to open the door when the washing cycle has not finished or the power supply is 
cut off during the washing cycle, as the temperature may be high and you may be scalded.

Disconnect the machine from the mains electricity supply and withdraw the plug from 
the socket before cleaning the machine.

The washing machine must not be hosed down. 

Cleaning the exterior 

Clean the exterior with a mild non-abrasive cleaning agent or soap and water using a  damp cloth. 
Wipe dry with a soft cloth.

Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaning agents.
 These might damage plastic surfaces and other components because of the chemicals
 they contain.

The washing drum

Clean the drum every 3 months by using the “Drum clean” programme.

Cleaning the drawer

Remove detergent residues regularly. Clean the drawer as follows:

Pull out the drawer until a resistance is felt. Press down the release catch and pull the drawer 
out of the machine.
Remove the siphon from compartment and clean it.
Clean the dispenser using a brush and warm water.

Summary of Contents for WMUK001W











Reviews: