background image

2X3 BAND TUBE EQUALIZER 

!

 

  if you notice smoke or an unusual odor 

  if any object or liquid gets inside the device,  

  if the device has been exposed to rain or other moisture,  

  if the device does not operate normally 

  Do  not  connect  the  appliance  to  a  mains  socket  to  which  an  electrical 

appliance  controlled  by  an  inverter,  switching  power  supply  (eg 
refrigerator, washing machine, microwave, air conditioner) or a appliance 
with a motor is connected. 

  Depending on the use of the electrical device, power supply noises may 

cause a malfunction or audible noise on this unit.If a separate electrical 
outlet cannot be used, connect a noise 

lter between this and the other 

electrical appliance. 

  The  appliance  heats  up  during  several  hours  of  continuous  operation. 

This is normal and not a cause for concern. 

  Turn o

 all devices before connecting the device to other devices. This will 

prevent damage to speakers and other equipment. 

  Use  of  the  unit  near  ampli

ers  or  other  equipment  that  contains  a 

transformer may cause noise. To resolve this issue, relocate the device or 
move it away from the interfering device. 

  Noise may be caused by using a wireless communication device near the 

device,  such  as    a  mobile  phone.  Such  noise  can  occur  when  making, 
receiving,  and  diverting  a  call.  If  you  experience  this  problem,  move  the 
wireless device away from the device or turn it o

  This unit may interfere with radio and television operation, so do not use 

near such receivers. 

  If the device is transported to a location with a very di

erent temperature 

and / or humidity, moisture may condense inside. Using the device in this 
condition  may  result  in  damage  or  malfunction.  Therefore,  wait  a  few 
hours  for  the  moisture  to  completely  evaporate  before  using  the 
appliance. 

!

 

!

2

Summary of Contents for EMPRESS GL-PEQ














Reviews: