GAI-Tronics 370-901 Manual Download Page 9

Pub. 42004-525A 

Model 370-901 SP2 to Page/Party

®

 Bridge 

Page 7 of 16 

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-525A.docx 
08/18 

Mute Connection—P5 

The muting conductor of the Page/Party

®

 system cable has no function in the SP2 to Page/Party

®

 Bridge.  

Terminal block 

P5

 provides a dead ended termination for the muting conductor of the Page/Party

®

 system 

cable (see Figure 4)

1.

 

Install a ferrule onto the end of the orange wire. 

2.

 

Connect the wire to pin one on pluggable terminal block 

P5

3.

 

Connect the pluggable terminal block to terminal block 

P5

Power—P1 

The SP2/Page/Party

®

 Bridge operates from a 120/230 V 

ac, 50/60 Hz power source.  AC power is connected at 
terminal block 

P1

1.

 

Pull the cable from the power source into the 
enclosure. 

2.

 

Install ferrules onto the wire ends. 

3.

 

Connect the line, and neutral, conductors to the 
pluggable terminal block (see Figure 4 and Table 6). 

4.

 

Connect the pluggable terminal block to terminal 
block 

P1

 

Close the Enclosure 

1.

 

Reconnect the front cover to the rear enclosure by pushing the hinge pins on the front cover into the 
holes on the left side of the rear enclosure until a click is heard. 

2.

 

Rotate the front cover to close the enclosure. 

3.

 

Install and tighten the four screws on the front cover. 

Configuration 

SP2 to Page/Party

®

 Bridges are configured using the GUDA (GAI-TRONICS Universal Device 

Application) software.  Install the GUDA software and run it to configure Page/Party

®

 bridges as follows: 

1.

 

Launch the GUDA application by double clicking the GAI-TRONICS Universal Device Application 
shortcut from the start menu. 

 

2.

 

Choose the network interface to perform the discovery. 

 

Table 6.  AC Power—P1 

Pin 

Label 

Description 

P1-1 

LINE 

ac hot 

P1-2 

 

no connection 

P1-3 

NEUTRAL 

neutral 

 

Summary of Contents for 370-901




















Reviews: