background image

 

 

Titan GSM  

29 

 

1234stat 

Where 1234 is the PIN code.   

The telephone will send back comprehensive information to assist 
maintenance and repair.  Compare this information with that recorded earlier 
to check if anything has changed that might indicate a problem. 

7.2.  Batteries 

The batteries fitted to Titan GSM are long-life, high performance batteries with 
an expected service life of 10 years under normal use. 

They must only be replaced by the correct type, ordered from GAI-Tronics, 
and must always be replaced as a pair. 

They are each held in place with 2 cable ties, and must be connected and 
linked by a fuse as shown in section 4.7. 

7.3.  Cleaning  

7.3.1 

General 

For normal cleaning we recommend "Virosol", manufactured by Clover 
products. 
Carefully follow manufacturer's instructions for storage, handling and 
use. 

7.3.2 

Anti graffiti coating 

Where polyurethane anti-graffiti coating or paint has been specified (as 
an option), it can be cleaned using Methylated Spirits or Methyl Isobutyl 
Ketone.  Other cleaners can be used but should be tested on a small 
area first. 

8.  Aftercare 

The purchase of your GAI-Tronics product does not end our commitment to 
you.  
 
In addition to our warranty obligations, GAI-Tronics are able to offer various 
levels of maintenance packages, installation and commissioning packages and 
technical support, from ad-hoc repairs to full maintenance contracts.  
 
By choosing GAI-Tronics as your aftercare provider you are ensured of 
manufacturer expertise and ISO 9001-certified quality control standards 
throughout the life of the product. 
 
We can also supply a full range of accessories including mounting posts, 
beacons and high-volume sounders. 
 
Contact GAI-Tronics for details.  

www.gai-tronics.co.uk

 

 

 

Summary of Contents for 230-02 Series





































Reviews: