background image

16

7.3 Nozzle replacement

Changing over to a different gas type

Only 

authorised specialists

are permitted to

change over to a different gas type.
The nozzles needed for conversion to propane gas
are included as a kit with this appliance. 
Nozzles can be replaced 

without having to open

the housing

.

Loads for all gases

For all gas types and pressures, the rated load 
is achieved by installing the high and low setting
nozzles for the required gas type (see nozzle
table).
The low setting nozzle is screwed in fully at the
works, and so the lowest quantity is set. 

Replacing the low-setting nozzle 1
Proceed as follows:

Disconnect the appliance from the power
supply!

– Remove the cover from the underside of the

appliance under the gas valves.
The low-setting nozzle 1 is located in the gas
valve and is screwed in from below. (see Fig. 10)

– Unscrew the nozzle and insert the new nozzle as

specified in the low-setting nozzle table. The
nozzle must be screwed in fully. Fit the cover
cap again.

If it should be necessary to correct the low-setting
nozzle 1 as the result of deviating gas types and
pressure, the flow rate can be increased by turning
to the left.

Fig. 10

See table on Page 12 

for details of nozzle settings.

Summary of Contents for KG260224CA





















Reviews: