11
2/19 REV. 4/23
GB713SH
-
CB S/N: 1011 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
IMPORTANT:
Be sure to use thread sealant on all hydraulic fittings, Loctite® 545 or equivalent or a non
-
hardening Teflon® thread
compound such as Slic
-
tite®. Tighten until fitting feels snug and then continue to tighten 1/2 to 1 full turn.
CAUTION:
Over tightening
can easily distort the threads. DO NOT USE TEFLON® TAPE.
CAUTION:
Teflon® tape is an excellent thread sealer, however, if it is not
properly applied, pieces of Teflon® may enter the hydraulic system and cause a malfunction or damage.
1.
Put the piston rod wrench assembly (704149) into the top of handle assembly (744129), pushing down firmly until piston rod
assembly (744136) is completely in the down position.
2.
Fill oil passage and reservoir with Automatic Transmission Oil Dexron® III or equivalent. The reservoir is the area surrounding
the power cylinder (743131). When looking at the top of the handle assembly (744129), the oil passage is the hole that has a
counter bore for o
’
ring (S832). Do not overfill causing oil to go in air passage hole.
3.
Install o
’
ring (S832), gasket (704129), button head cap screws
(
A
-
928) and manifold
-
handle (744303) to handle assembly (744129),
keeping hydraulic hose (A
-
317) towards plug (704313). Torque button head cap screws
(
A
-
928) to 40 inch lbs. (4.52 Nm).
Push piston (713211) full forward. Install gasket (704129), o
’
ring (S832) and button head cap screws (402479) on handle assembly
(700343). Assemble head cylinder assembly (713123) to handle assembly (700343). Apply Loctite® 242 to all socket head cap
screws and torque to 40 inch lbs. (4.52 Nm).
Coil tool up on bench and lay manifold
-
handle (744303) down on side so that the hole marked #4 on the side of the manifold
-
handle (744303) is to the top. Rest head cylinder assembly (713123) over a small bucket or can. Completely fill up fill bottle (745263).
6.
Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from manifold
-
handle (744303) hole marked #4. Connect fill bottle
(745263) to manifold
-
handle (744303) hole marked #4. Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from bleeder
hole on head cylinder assembly (713123).
7.
In one continuous squeeze force oil into manifold
-
handle (744303) until oil starts to flow from bleeder hole on head cylinder
assembly (713123). While still squeezing the fill bottle (745263), use other hand to replace button head cap screw (402482) and
stat
-
o
-
seal (S572) on the head cylinder assembly (713123) and torque to 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not over tighten. This may
require two people.
8.
Remove fill bottle (745263) from manifold
-
handle (744303) hole marked #4 and replace stat
-
o
-
seal (S572) and button head cap
screw (402482) and torque to 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not over tighten.
Hole marked #4 on Manifold
Handle (744303)
Fill Bottle (745263)
Oil Passage hole
O
’
ring (S832)
Handle Assembly and
Power Cylinder hole
***Keep air
hole free
from oil***
Images may not reflect actual tool.
FILLING PROCEDURE
WARNING:
Do not cycle tool without air bleeder assembly (704153), or the screw and stat
-
o
-
seal, installed in tool head. Severe
personal injury could result.
WARNING:
Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be
under pressure.
CAUTION:
Before filling handle assembly (744129), air piston assembly (744121) must be all the way down.
CAUTION:
When forcing piston rod assembly (744136) downward, with head cylinder assembly (713123) removed, hydraulic oil will eject
forcibly from handle assembly (744129).
CAUTION:
When bleeding tool, ensure tubing is free from kinks or other obstructions.
Note:
•
Fill bottle (745263) (sold separately) is required.
* FILLING & BLEEDING VIDEO AVAILABLE AT:
http://www.gagebilt.com/rivet_tools_videos.php
Bleeder hole on head cylinder
assembly (713123)
