Gage Bilt GB703SHVTPTS, Original Instructions Manual

Page: 20 / 24

20 11/21 REV 5/22
GB703SHVTPTS: INSTALLATION TOOL
NOSE ASSEMBLY SELECTION CHART FOR XX - 703 - 18VPSA
(Sold Separately)
RIVET DIA. NOSE ASSEMBLY NOSE TIP
1
RELEASE FOLLOWER
3/16 AV6-743-24VPSA
2
----- ----- -----
3/16 6C-743-24VPSA
2
----- ----- -----
3/16 6KT-703-18VPSA
1
703342 703343 703415
1/4 8KT-743-24VPSA
2
----- ----- -----
MACHINE SCREW RIVET
5MM MS5M-703-18VPSA
1
703348 703349 703415
3/16 MB06-734-20VPSA
2,5
----- ----- -----
1/4
3
MB08-734-20VPSA
2,5
----- ----- -----
3/32 3NP-703-18VPSA
1
703338 703339 703421
1/8 5N-703-18VPSA
1
703328 703329 703415
3/32 3N-703-18VPSA
1
703336 703337 703421
1/8 4N-703-18VPSA
1
703338 703339 703421
5/32 5N-703-18VPSA
1
703328 703329 703415
3/16 6N-703-18VPSA
1
703334 703335 703415
1/4
3
8Z-743-24VPSA
2
------ ----- -----
3/16 6P-703-18VPSA
1
703340 703341 703415
1/4 8P-743-24VPSA
2
----- ----- -----
3/16 6T-703-18VPSA
1
703334 703335 703415
1/4
3
8T-743-24VPSA
2
----- ----- -----
TLR RIVET
1/4 8TLR-743-24VPSA
2
----- ----- -----
RIVET DIA. NOSE ASSEMBLY NOSE TIP
1
RELEASE FOLLOWER
3/16 PH6-734-20VPSA
2,5
----- ----- -----
1/4
4
PH8-734-20VPSA
2,3,5
----- ----- -----
1) YOU CAN CHANGE THE 703 NOSE ASSEMBLY (INCLUDED WITH TOOL) TO INSTALL OTHER FASTENERS BY PURCHASING NOSE TIP AND
2) NOSE ASSEMBLIES WITH A 743 DESIGNATION, I.E. 8Z-743-24VPSA, MUST BE ORDERED AS COMPLETE NOSE ASSEMBLY.
3) ALUMINUM RIVET STEEL MANDREL ONLY (100 PSI REQUIRED FOR ALL 1/4" STEEL RIVETS).
4) 1/4" ALUMINUM ONLY.
5) NOSE ASSEMBLIES WITH A 734 DESIGNATION, I.E. PH6-734-20VPSA, ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH
AND SERRATED STEM RIVETS YOU MUST ORDER THE NOSE ASSEMBLY WITH A 743 DESIGNATION, I.E. MGL06-743-24VPSA.
RELEASE SHOWN AND USING APPROPRIATE FOLLOWER SHOWN.
T RIVET
OPEN END
CLOSED END
NAIL RIVET
KLAMPTITE (STRUCTURAL) RIVET
MONOBOLT RIVET
NUTPLATE RIVET
CCR244/264/274
BACR15DR
MS20600
AVEX (1624 PROTRUDING HEAD)
AVEX (1624COUNTERSUNKHEAD)
EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
SERRATED STEM
STRUCTURAL RIVET
SELECTION CHART FOR PROTRUDING HEAD ONLY
PLASTIC SPLIT RIVET
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE
Non - removable Loctite® 242 was applied to anvil
holder (10757) during assembly to lock sleeve
(703327) in place. If disassembled, re
- apply non -
removable Loctite® 242 as shown before tightening
sleeve (703327) to end of thread.
*Apply Vibra - tite® part# 405125 to all
threads and allow it to set 20 minutes
prior to assembly.